DSC BRAVO5 Instrukcje instalacji

Przeglądaj online lub pobierz pdf Instrukcje instalacji dla Czujniki bezpieczeństwa DSC BRAVO5. DSC BRAVO5 2 stron. Ceiling mount pir detector

Drukuj stronę

INSTALLATION INSTRUCTIONS

The Bravo5 is a ceiling mount detector designed to

provide reliable motion detection for residential

and commercial applications. The Bravo5 uses a

special Fresnel lens made for 360° detection in

conjunction with a quad element PIR sensor

optimized for uniform detection all around its field

of view. Special attention is given to false alarm

immunity against RF, static, electrical transient to

ensure trouble free operation for many years.

Features

• Multi-Level Signal Processing

• 360° coverage

• Quad element PIR sensor

• High level static and transient protection

• Excellent RF immunity

• Temperature compensation

• Fast/Slow detection jumper

• LED ON/OFF jumper

• SMD construction

• Super quiet operation

• 5 year warranty

Specifications

Electrical

• Input Voltage: 9 - 14.5 V

• Current (nominal): 18 /15 mA (alarm on/off) @12 V

Contact Rating

• Alarm Relay: 0.1A @24V

• Tamper Switch: 0.1A @24V

Size (diameter x height)

4.6" x 1.4" / 117 mm x 36 mm

Operation

• Maximum detection range (diameter)

Ceiling Mount

Detector placed 8 ft./ 2.4 m from floor: 24 ft./ 7.3 m

PIR Detector

Detector placed 10 ft./ 3.0 m from floor: 30 ft./ 9.2 m

Detector placed 12 ft./ 3.6 m from floor: 40 ft./ 12.2 m

• Additional operating modes

LED ON/OFF Jumper J1

Pulse count (fast/slow) Jumper J2, J2 ON is fast count.

Environmental/Immunity

• RF Immunity: 20V/m ( 100Hz - 1.2GHz)

• Transients @ wiring terminal: 2.4KV @ 1.2joules

• Operating temperature: 32 -122°F / 0 - 50°C

• Humidity 5 - 95% RH non-condensing

Product Information

• BV-500: Form 'A' alarm contact

• BV-501: Form 'A' alarm contact and tamper switch

• BV-502: Form 'C' alarm contact and tamper switch

Coverage

Top View (at 8 ft./ 2.4 m height)

Side View

Patented

Locating the Detector

The Bravo5 is designed to be mounted on the ceiling of a

dry indoor location for 360° coverage. Ensure that the

expected path of an intruder is perpendicular to the beam

path. Use the coverage pattern indicated on the coverage

diagram to determine the best sensor location.

Survey the mounting location and the area being protected

for the following potential problems. Avoid the following

sources of false alarms:

Reflective Surfaces

Do not aim the detector at reflective surfaces such as

mirrors or windows as this may distort the coverage pattern

or reflect sunlight directly onto the detector.

Air Flow

Avoid locations that are subject to direct high air flow such

as near an air duct outlet.

Moisture

Do not locate the detector near sources of steam or oil.

The Sun

Do not aim the detector such that it will receive direct sunlight.

Obstructions

Do not limit the coverage by placing large objects within the

detection area (such as plants, high shelves, filing cabinets etc.).

Mounting

To open the case, insert a small screwdriver in the tab

restraining clip. Gently pry tab downward and twist the top

cover counter-clockwise and lift it up from the bottom cover.

Use a small screwdriver to remove the appropriate

knockouts for wiring. Mount the bottom cover using the

screws supplied.

To close the case, use the locating line on the bottom cover

to align the tab on the top cover. Once the top cover is

engaged, twist the top cover clockwise to lock it in place.

NOTE: Since no adjustment is necessary for the circuit

board, it is not recommended that the installer remove the

circuit board from the case.