DSC RXL2-433 Instrukcja instalacji

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Jednostka sterująca DSC RXL2-433. DSC RXL2-433 2 stron. Universal wireless relay module

Drukuj stronę

2. Every time I press the button for relay # 1 both lasers turn on for 1 minute.

Make sure you have the MODE programmed correctly. See section 4.3.

3. I hear the relay 'click' but the garage door won't open or close.

Verify that you have wired the correct relay output to the garage door push button. Make

sure you have wired across the push button of the garage door.

4. The garage door opens and closes but the push button no longer works.

Check to verify that you have wired across the push button of the garage door typically

labeled #1 and #2 on most garage doors. Please consult the garage door opener

instructions for proper connection.

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved by Digital Security Controls could void your authority to use

this equipment.

This equipment generates and uses radio frequency energy and if not installed and used properly, in strict

accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type

tested and found to comply with the limits for Class B device in accordance with the specifications in Subpart "B" of Part 15 of

FCC Rules, which are designed to provide reasonable protection against such interference in any residential installation.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

interference to television or radio reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Re-orient the receiving antenna

• Relocate the alarm control with respect to the receiver

• Move the alarm control away from the receiver

• Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits.

If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user

may find the following booklet prepared by the FCC helpful: "How to Identify and Resolve Radio/Television Interference

Problems". This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402,

Stock #004-000-00345-4.

This Class B digital apparatus meets all requirements of the Canadian interference-causing equipment regulations.

Cet appareil numerique de la Classe B respecte toutes les exigences de reglement sur le materiel brouilleur du Canada.

IC: 160A-RXL2433

The term "IC:" before the radio certification number only signifies that Industry Canada technical specifications were met.

RXL2-433 version 1.0

WARNING: Please refer to the System Installation Manual for information on limitations

regarding product use and function and information on the limitations as to liability of

the manufacturer.

Toronto, Canada • www.dsc.com

Tech Support: 1-800-387-3630 or 905-760-3036

Printed in Taiwan

Installation Instructions

29007102R002

RXL2-433 v 1.0 Installation Manual

Section 1: Introduction

The RXL2-433 universal wireless relay module is designed to allow unparalleled flexibility and

convenience when adding additional wireless features to any DSC wireless key. This manual

describes how to install, program and maintain the RXL2-433. Please read the entire manual

before installing the product.

1.1 Specifications and Features

• Supports up to 20 different wireless buttons 10 per output

• Frequency: 433 MHz

• Outputs: (2) Form 'C' relays 30VDC, 3A (max.)

• Power: 12VDC plug in transformer (included)

• 32° to 120°F (0° to 49°C)

• 5-93% RH

• Included in Kit: 1 Receiver, 1-120V Transformer, 2 Receiver Mounting Screws, Velcro

1.2 Compatible Wireless Keys

Please refer to the installation sheets of the following keys for more information. The RXL2-433

can receive signals from the following keys:

• WS-4939

• WS4949 (3 channel wireless key)

• WS4969

Section 2: RXL2-433 Set up and Wiring

This section describes how to set up and wire the RXL2-433 module.

2.1 Choose a Mounting location for the RXL2-433 module

The receiver should be placed in a location that is:

•Dry

• Close to the point of operation.

NOTE: Ensure that electrical wires do not run over the antenna when it is mounted.

2.2 Terminal Description

The RXL2-433 has 2 on-board relays which can be used in many different applications. They

can be used to activate garage doors, security gates, Trigger X-10 devices etc.

2.3 Connecting to a Garage Door

The RXL2-433 can be mounted using the supplied screws. Make sure to mount the receiver

with the antenna wire hanging freely towards the ground. Connect relay #1, NO and C

terminals, to garage door push button #1 (The push button is typically labeled #1 and #2 at the

motors terminal strip for most manufacturers). If you are connecting the RXL2-433 to a second

garage door, connect a pair of wires from garage door #2's push button OR motor to Relay #2.

Please consult the garage door opener instructions for proper connection. Plug in the supplied

AC/DC transformer. The RXL2-433 is defaulted to a 'Momentary' relay output, if you have

changed the output to a different type you must reset the relay to 'Momentary' for the garage

door to operate correctly. See Section "How to Program Relay #1 Output."

• WLS919-433

• WS4959 (12 channel wireless key)

FIGURE 1