DSC Maxsys PC4612 Instrukcje instalacji

Przeglądaj online lub pobierz pdf Instrukcje instalacji dla Alarm dymowy DSC Maxsys PC4612. DSC Maxsys PC4612 2 stron. Fire zone annunciator

Drukuj stronę

PC4612 Annunciator

Introduction

The PC4612(A) is a 12-zone fire annunciator for use with

PC4010/PC4020 security systems. You can install a combined

total of 9 PC4612(A) and PC4216 modules on each PC4010/

4020 system.

Specifications

• Style PC4612 or PC4612A available

• 16 programmable LEDs

• Four wire (QUAD) hook-up to Combus

• Nominal current draw of 15mA

• Tamper and trouble reporting

• Supervision by control panel via Combus

Installation

Connect the PC4612(A) to the panel via the Combus. Be sure

to include the current draw of the PC4612(A) (15mA) in your

Combus current calculation. Refer to your PC4010/4020

Installation Manual for more information on Combus

wiring.

Enrolling and Programming the PC4612(A)

Follow the instructions below for enrolling and

programming your PC4612(A) module. If you are enrolling

the module on a PC4010/4020 v3.0 or greater system, you

can use the reference numbers (indicated by the square

brackets, eg. [0200]) to jump to a programming section. Refer

to your system's installation or programming manual for

more information on programming.

4.1 Enrolling

You must enroll the PC4612(A) module with your panel

before you can program it. The PC4612(A) is enrolled exactly

as if it were a PC4216 module. Follow these steps:

At a PC4010/4020 system LCD keypad, enter Installer's

Programming ([*][8][Installer's code]).

Enter Ref #[0200][*] OR scroll to Module Hardware,

press [*], then, scroll to Enroll Module, press [*].

Scroll to PC4216 Module, press [*]. The LCD keypad

displays Create Tamper on Desired Unit.

Tamper and then restore the PC4612(A):

1. Remove the screws on the bottom of the unit.

2. Pull the front plastic of the unit approximately ¼"

away from the backplate.

Please refer to the System Installation Manual for information on limitations regarding product use

and function and information on the limitations as to liability of the manufacturer.

PC4612(A) Fire Zone Annunciator

PC4612A Annunciator

3. Replace the front of the unit and the screws in their

original locations.

The LCD keypad displays PC4216 Mod 01 Enrolled.

Record the module number in the worksheet area on

the back of this instruction sheet.

To exit Module Enrollment, press [#].

4.2 Programming

On the PC4612(A), each of the 16 outputs controls a particular

LED. Outputs 1-12 control the LEDs which light up numbers

1-12 on the Annunciator. Outputs 13-16 control the LEDs

which light up the Zone Trouble, Bell Trouble, System Trouble

and AC On indicators, respectively.

A Custom Group is a set of 16 programming choices which

correspond to the 16 programmable outputs on each

PC4612(A) module. Each LED will function according to the

programming of its output in the assigned custom group.

To program the PC4612(A), you need to assign a custom

group to the module, and to make sure that the outputs of

the assigned custom group are programmed appropriately.

Example: the PC4612(A) is assigned to custom group (01). In

this custom group, output (05) is programmed to follow zone

(020), which is a fire zone. This was done by programming

output (05) for option (22) zone follow. When zone (020) is in

alarm, LED 5 turns on. When zone (020) is restored and a

fire reset is performed, LED 5 turns off.

The PC4612(A) uses the same programming as the PC4216,

and is therefore done in the same programming sections. These

sections are described below as they relate to the PC4612(A).

For instructions on how to program the PC4010/4020 and its

modules, refer to your PC4010/4020 Installation Manual. For

information on programming PC4216 modules, refer to your

PC4216 Installation Instructions.

1. Choose a Custom Group

Ref #: [000703XX] where XX = 01-09 (PC4612(A) number)

Program each PC4612(A) to use one of nine custom groups.

More than one module may follow the same custom group.

Enter the number of the custom group the PC4612(A) will

follow (enter 01-09). To exit, press [#].

2. Program a Custom Group

Ref #: [000704XX] where XX = 01-09 (Custom Group 01-09)

A custom group is a set of 16 programmed output options.

Each output in a custom group can be programmed to operate

according to a different output option.