AirTight 60398 Instrukcja obsługi - Strona 2

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Elektronarzędzie AirTight 60398. AirTight 60398 2 stron. 120v compact tire inflator

Drukuj stronę

FEATURES & SPECIFICATIONS

• 120V Tire Inflator

• Dial Pressure Gauge

• On/Off Switch

• Cooling Fan

• 27 in. Air Hose

• 6 Ft. Power Cord

• Air Accessories Include: Sports Ball Needle, 6 Raft, Mattress & Toy Inflator Nozzles

IMPORTANT SAFETY INFORMATION

WARNING Read and understand all

• NEVER use in traffic or other unsafe areas.

instructions before use. Failure to follow

instructions can result in personal injury and/or

• NEVER leave the inflator running unattended.

property damage. Save these instructions for

future reference.

• DO NOT carry the inflator by the air hose or

power cord as damage may occur.

WARNING

• KEEP OUT OF THE REACH OF CHILDREN.

• Disconnect power when not in use.

The inflator is not a toy and is not intended for

use by children.

• Do not operate inflator near flammable liquids

or in gaseous or explosive atmospheres.

• This inflator is designed to inflate car tires, bike

Internal sparks may ignite fumes.

tires, ATV tires, sports equipment, air

mattresses, beach toys and other inflatables.

• Do not operate or store your inflator in a damp

DO NOT USE FOR ANY PURPOSE OTHER

or wet locations.

THAN INFLATING. BODILY HARM OR

PERSONAL INJURY CAN OCCUR.

• Keep inflator dry, clean, and free from oil and

grease. Always use a clean cloth when cleaning.

• NEVER exceed the manufacturer's

Never use brake fluids, gasoline, petroleum-

recommended pressure for any inflatable object.

based products, or any strong solvent to clean

DO NOT OVER-INFLATE OBJECTS. Over

the inflator.

inflation can cause personal injury and/or

property damage.

• Operate the inflator only with the attachments

that are included.

CAUTION

• HOT - Do not hold in hand while operating.

• USE SAFETY GLASSES. Also use face or dust

Place compressor on ground during use.

mask if operation is dusty.

• DO NOT run compressor for more than 10

• THIS INFLATOR IS NOT DESIGNED TO FILL

minutes continuously.

AIR TANKS OR AIR SHOCKS.

• ALLOW THE COMPRESSOR TO COOL AT

LEAST 10 MINUTES AFTER EACH 10

MINUTES OF CONTINUOUS USE.

CONNECTING TOOL TO POWER SOURCE OUTLET

The power source must be grounded

while in use to protect the operator from

electric shock. In the event of a malfunction

or breakdown, grounding provides a path of

least resistance for electric current to reduce

the risk of electric shock. This tool is

equipped with an electric cord having an

equipment grounding conductor and a

grounding plug. The plug must be plugged

into a matching outlet that is properly

installed and grounded in accordance with

all local codes and ordinances.

This tool is intended for use on a circuit that has an outlet that looks like the one illustrated in

Figure A. The tool has a grounding plug that looks like the one also shown in Figure A. DO

NOT modify the plug provided if it will not fit the outlet. Have the proper outlet installed by a

professional electrician.

Use only a 3-wire extension cord that has a 3-blade grounding plug, and a 3-slot receptacle

that will accept plug on product.

2. Make sure extension cord is in good condition, and heavy enough to carry the current the

product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power

and overheating.

3. The chart (shown below) shows correct size to use depending on cord length. If in doubt,

use the next heavier gauge.

Note: The smaller the gauge number, the heavier the cord.

Recommended Extension Cords

Length of Cord (ft)

Gauge of Cord

FUSE REPLACEMENT

When replacing the fuse, make sure the inflator is turned off and nothing is connected to the

tire inflator.

1. Unscrew the top of the fuse holder.

2. Replace the fuse with a new 2-amp fuse. Always replace a blown fuse with the same size fuse.

3. Screw the top of the fuse holder back on to the unit.

OPERATING INSTRUCTIONS - TIRES

1. Confirm that the power switch on the inflator

is in the "O" (OFF) position.

2. Remove valve cap from stem.

3. Attach the universal adapter from the inflator

to the valve stem with the lever in the up

position. Be sure to press universal adapter

down over valve stem threads completely. When

universal adapter is firmly in place, press locking

lever down to lock onto valve stem.

4. Plug power cord into 120V power outlet.

5. Turn inflator power switch to "I" (ON)

position and inflate to the manufacturer's

recommended air pressure.

OPERATING INSTRUCTIONS - INFLATABLES

1. Confirm that the power switch on the inflator

is in the "O" (OFF) position.

2. To use the inflation accessories, snap either

piece into the universal adapter and push the

lever to lock into place. The inflation accessory

will fit securely.

3. Plug power cord into 120V power outlet.

4. Insert the appropriate inflation accessory into

the inflatable object (tire, football, raft, etc.).

NOTE: If a pressure reading is required during inflation, the built-in pressure gauge will

provide an estimated reading only. Please use a digital pressure gauge to check the actual

pressure on the inflated object for more accurate pressure information.

100

150

TROUBLE SHOOTING

INFLATOR DOES NOT WORK WHEN

SWITCHED TO "ON"

• Power cord may not be plugged in completely.

Check the connection.

• Fuse may have blown. Unplug the unit and

check fuse located on front of unit. NEVER

replace a blown fuse with a fuse having a

higher rating. See "Fuse Replacement" on page

3 of this manual.

6. Once desired pressure is reached, turn power

switch to the "O" (OFF) position.

7. Unplug the power cord from power outlet.

8. Remove the universal connector from

the tire valve.

When inflating truck or trailer tires requiring

pressure greater than 50 psi, it is

recommended that the tire is deflated

manually to 40 psi or less before beginning

inflation. This operation allows the inflator to

gradually reach the desired pressure and

prevents the inflator's pump from stalling.

5. Turn inflator power switch to "I" (ON) position

and inflate to the manufacturer's

recommended air pressure.

6. When the object is firm, turn power switch to

the "O" (OFF) position. DO NOT OVER

INFLATE OBJECTS.

7. Unplug the power cord from power outlet.

UNIT IS RUNNING BUT TIRE

IS NOT INFLATING

• Check that the air hose connector is attached

properly to the tire valve stem.

• Check for tire leaks or damage, and check air

hose for breaks and leaks at fittings.

INFLATOR FEELS HOT OR RUNS SLOWLY

• Unit may have overheated. Shut the unit off

and allow to cool for 20-25 minutes.

• NEVER use this inflator for more than 10

minutes continuously.