3onedata ES1008G-8POE-150W-P Podręcznik użytkownika - Strona 2
Przeglądaj online lub pobierz pdf Podręcznik użytkownika dla Przełącznik 3onedata ES1008G-8POE-150W-P. 3onedata ES1008G-8POE-150W-P 3 stron. Full gigabit unmanaged poe switch
Drukuj stronę
10Base-T/100Base-TX/1000 Base-TX Ethernet port use in
front panel, It is RJ45 port, the PIN define of RJ45 is as follows:
connection adopt UTP or STP, the distance is no more than 100m,
1000Mbps use cat5e, 100Mbps use cat5, 10Mbps use cat3,4, 5.
RJ45 port support MDI/MDI-X self-adaption. In (MDI),
PIN1, 2, 3, 4, 5, 6, 7, 8 connect corresponding, in (MDI-X)
PIN1→3, 2→6, 3→1, 6→2, 4→7, 5→8, 7→4, 8→5. In
MDI/MDI-X, 1000 Base-TX PIN define is as follows:
1
8
10/100Mbps
1000Mbps
PIN
MDI
MDI-X
MDI
1
BI_DA+/TX+
TX+
RX+
2
BI_DA-/TX-
TX-
RX-
3
BI_DB+/RX+
RX+
TX+
4
BI_DC+/—
-
-
5
BI_DC-/—
6
BI_DB-/RX-
RX-
TX-
7
-
-
BI_DD+/—
8
-
-
BI_DD-/—
Note："TX±"Transmit Data±， "RX±"Receive Data±， "—"Not Use。
MDI (straight-through cable):
MDI-X (Cross over cable)
MDI/MDI-X auto connection makes switch easy to use for
customers without considering the type of network cable.
【LED Indicator】
The POE Switch indictor light on the front panel. the function of
MDI-X
each LED is described in the table as below.
BI_DB+/RX+
Indicat
LED
BI_DB-/RX-
or
BI_DA+/TX+
ON
PWR
BI_DD+/—
OFF
BI_DD-/—
Blinking
BI_DA-/TX-
Destroy/
Sys
normall
BI_DC+/—
y on
BI_DC-/—
ON
Flashing
Link/A
CT
OFF
Yellow
Description
Power connection regularly
Power supply have no connection or
unwonted
Software running in the CPU
The software runs abnormally in the CPU
Established effective network connection
Network in activity statues
Did not established effective network
connection
The 10/100M ports auto-negotiate
connected
The 1000Mbps ports auto-negotiate
Green
connected
ON
The POE function works
POE
The POE ports failed to work or the PDs
Flashing
are overloaded
【Installation】
Operation Cautions
1)
Don't stock the device in damp environment or near
water, to avoid water or moisture penetrating into the
inner device.
2)
Don't put the device on a unstable box or desk, the
device will get damaged from falling.
3)
Please check and make sure the operation voltage is
meet the voltage standard marked on the device surface
before the next steps.
4)
Please use a grounded three-hole power socket in the
rack or desk mounting, to mitigate damage caused by
electro-static discharge or lightning stoke.
5)
Keep the device far from heat sources, strong power
radio transmitters and radar transmitters.
6)
Similar with other electrical products, the semiconductor
chip in device will get damaged when open and shut off
the power frequently. Please restart the device 3~5
seconds(or longer) after the power is shut off.
7)
Please pull out the power plug before cleaning the
device. Don't wipe the device with wet cloth or clean the
device with liquid.
8)
To guarantee a long operation life, the device can only
be used in indoor and in ventilated & dry environment.
And to get a good heat dissipation, please reserve a
space over 10CM around the device.
Rack Mounting