Attwood 66382 Instrukcje instalacji

Przeglądaj online lub pobierz pdf Instrukcje instalacji dla Oświetlenie morskie Attwood 66382. Attwood 66382 1 stron. 2-mile transom lights

Drukuj stronę

2-Mile Transom Lights

Models 6356D and 66382

Installation Instructions

Attwood marine hardware, navigational lighting, bilge pumps, and

other marine accessories are specified more than any other brand

by America's best-known boat manufacturers as original equipment.

Look to Attwood for quality replacement parts and marine accessories.

SAVE THESE INSTRUCTIONS

Form Number 69396 Rev. B

WARNING

Read all instructions carefully before installing and using this product.

To prevent personal injury, disconnect the power source when installing

or servicing this product. Always remove the boat from the water before

using 120V AC power tools.

Use only the fuse amperage rating specified in these instructions.

FEATURES

These Attwood Transom Lights are for use on boats up to 65.6 ft.

(20 meters). The 6356D Transom Light (Round) has a clear backing

so it shines on both sides of a bulkhead - can be used to light an

interior compartment.

6356D Transom Light meets USCG CFR 183.810, ABYC A-16

requirements, and all applicable standards as tested by Imanna

Labs, 12/20/2002. 2 Nautical-Mile visibility. Lights use 7.5-watt

lamp, #9232 (13-volt).

REQUIRED FOR INSTALLATION

• Phillips screwdriver

• Cordless drill; 1/8" (3mm) bit and 1-7/8" (48mm) hole saw

• 16-gauge wire and waterproof crimp connectors

• Fuse holder (Attwood #14341) and 1-amp fuse

INSTALLATION LOCATION

Transom Lights must be mounted:

• On the transom, exterior cabin bulkhead or superstructure. (Figure 1)

• As far aft as possible.

• On a vertical surface where the light will be unobstructed.

• So that light shines directly astern and horizontally when the boat

is floating.

Figure 1

INSTALLATION

1. To access light base mounting holes, remove the 2 mounting screws,

bezel, and lens. Set these aside for reinstallation. (Figure 2)

2. Place flat side of base against a smooth vertical surface

(see INSTALLATION LOCATION for proper position).

Important: Before drilling, be sure that light will shine straight astern

and within 5 of horizontal when boat is floating.

3. Use base as a template to mark location of two mounting holes

and a center hole for wire access.

CAUTION

Position wire access hole carefully, especially on aluminum boats,

so that wires do not contact the hull.

4. Drill 1-7/8" (48mm) diameter hole for base clearance and 1/8" (3mm)

diameter holes for mounting screws. (Figure 2)

Figure 2

1/8" (3cm)

Pilot Hole

1-7/8" (48mm)

Base Clearance Hole

03-10

5. Bring one 16-gauge (+) and one (-) wire up through access hole.

DO NOT connect these wires to power until you read FINAL

WIRING INSTRUCTIONS. (Figure 3)

6. Connect wires using waterproof crimp connectors.

7. Place gasket and base over clearance hole. Replace lens and

bezel. Fasten assembly with two supplied mounting screws.

DO NOT OVERTIGHTEN.

FINAL WIRING INSTRUCTIONS

Connect to 12-Volt DC power source ONLY. All positive wires must

be protected by a 1-amp fuse. Higher voltage or failure to make

proper wire and fuse connections will void the product warranty.

Use crimp type marine-grade connectors with suitable insulation.

Figure 3

(pos)

1. Neatly thread wires to the switch, avoiding areas where abrasion

or snagging may occur.

2. Use switch (Attwood #14386 or equivalent) that allows two-position

ON/OFF/ON operation - one for running lights, and one for anchor

lights. Attach wires with crimp-on butt joint connectors. Test lights

for proper operation.

MAINTENANCE

To replace lamp or lens: Remove the bezel and lens (Figure 2).

Lamp: 7.5 watt, 12-volt (Attwood #9232).

Lens: Attwood # 6356-03 (Round) or #911259 (Square).

Replace lens, helmet, and retaining screws.

ATTWOOD LIMITED WARRANTY

This product carries the standard Attwood one-year warranty.

See Product Catalog or www.attwoodmarine.com for details.

1016 N. Monroe Street, Lowell, MI 49331-0260 www.attwoodmarine.com

Lamp

Attwood #9232

Base

1-Amp Fuse

(neg)

(pos)

12V DC

(neg)

Bezel

Mounting

Screws

Lens

#6356-03 (round)

#911259 (square)

3-Way Switch