Attwood 4650 Instrukcje instalacji

Przeglądaj online lub pobierz pdf Instrukcje instalacji dla Pompa wodna Attwood 4650. Attwood 4650 2 stron. Tsunami aerator pump

Drukuj stronę

Tsunami Aerator Pump

Installation Instructions

SAVE THESE INSTRUCTIONS

Form Number 69391 Rev. A

DANGER

If Aerator is installed thru-hull, remove boat from water to service

this pump. Do not use this pump to remove gasoline or other

flammable liquids.

WARNING

Most of the aerator pump, plumbing and connections are below the

water level. Do not attempt to install, adjust, service or remove this

product while the boat is in the water. Failure to follow these instructions

could result in a large volume of water flooding and sinking your boat.

Any leak will allow water to enter the boat.

To prevent personal injury, always disconnect the power source when

installing or servicing any electrical product.

Use the fuse amperage rating specified for your model pump.

Refer to Specification and Accessories Charts to be sure you have

selected the proper components:

Specifications Chart

12-Volts DC

ABYC Specifications

(GPH = Gal. Per Hour) (LPH = Liters Per Hour)

0 ft.

Hole

Head

Part

Saw Amp

GPH/

Num. Series

Size Fuse amps

4640 500

1-1/8" 2.5A 500/1.8 440/1.8 265/1.8 1705/1.5 1420/1.5 10' 5"/30

4650 800

1-1/8" 4A

800/3.0 670/3.0 525/3.0 2900/2.6 2350/2.6 14'/35

4660 1200

1-3/8" 5A

1200/3.5 900/3.5 700/3.5 4320/3.4 3145/3.4 10' 5"/26

Accessories Chart

3/4" O.D. Outlet Models

Inlet

3/4"

3/4" O.D. Threaded

Part

Hose Inlet Hose

Thru

Num. Series I.D. Connector

Hull

4640 500

3/4"

3899

66547

4650 800

3/4"

3899

66547

1-3/8" O.D. Outlet Models

1-1/8"

Inlet

1-1/8"

O.D.

Part

Hose Inlet Hose

Thru

Num. Series I.D. Connector

Hull

4660 1200 1-1/8"

3902

66548

MOUNTING LOCATIONS

1. The aerator can be mounted directly through the transom, at least

2" (51mm) below the static water line. (Figure 1)

ISO Specifications

@13.6 VDC

@12.0 VDC

3.3 ft

6.7 ft

0kPa

10kPa

Head

GPH/

LPH/

amps

3/4"

S.S.

Outlet

Remote

Inlet

Spray

Connector Bracket Strainer Head

3890, 90˚ 4122

4232

4125

3890, 90˚ 4122

4232

4125

1-3/8"

Threaded

S.S.

Outlet

Remote

Inlet

Spray

Connector Bracket Strainer Head

3902, 90°

4121

4234

4127

Figure 1

Allow Clearance to

Access Hose Clamp

and Locking Tab

Outlet

Connector

10-03

1/8" (3mm) Min.

1 7/16" (37mm) Max.

2. The aerator can also be remotely installed on a marine-plywood

mounting pad. This requires an Attwood Remote Bracket — see

Accessories Chart for size. (Figure 2)

Figure 2

Outlet

Connector

Remote Bracket

Suitable Mounting Pad

IMPORTANT: To avoid airlock, do not allow dips or sharp bends in

outlet or inlet hoses.

DIRECT MOUNTING INSTRUCTIONS

Max

See Accessories Chart for size / part number of Outlet Hose Connector.

Head

([email protected]/

1. With boat out of the water, select a suitable location at least 2"

kPa@12v)

(51mm) below the water line. Use a hole saw (See Specification

Chart for size — compare against aerator inlet) to drill a hole

through the transom. (Figure 1)

2. Apply polyurethane marine sealant (Boat-Life Lifeseal

to the nut and to threaded side of the aerator flange.

3. Install the aerator inlet through the transom and assemble the nut.

Tighten the nut handtight. Use wrench to tighten 1/2 additional turn.

WARNING

DO NOT EXCEED these tightening specifications.

4. Install Attwood 90° Outlet Connector to the aerator outlet. Tighten

Replacement

the fitting handtight, then 1/4 to 1/2 additional turn with wrench.

Motor

5. Use an Inlet Strainer to avoid clogging of the pump.

Cartridge

REMOTE MOUNTING INSTRUCTIONS

4620

See Accessories Chart for sizes / part numbers of Thru-Hull, Bracket,

4622

and Inlet Hose.

1. With boat out of water, install Thru-Hull Connector through the

transom. (Figure 2)

Replacement

CAUTION: DO NOT drill through the bottom of the boat when installing

Motor

Remote Bracket.

Cartridge

2. Attach Remote Bracket to the mounting pad by drilling two 1/8"

4624

(3mm)-diameter pilot holes and fastening with two #8 stainless

steel pan head screws. Position aerator on Bracket so pump outlet

is pointed straight up.

3. Complete outlet fitting and hose connection as described above.

4. Connect a length of reinforced, smooth bore Inlet Hose from the

Thru-Hull to the aerator Inlet Hose Connector. Use a hose clamp

at each end of the hose.

Transom

2" (51mm) Minimum

Inlet Strainer (optional)

3/8" (10mm)Thread

Allow Clearance to

Access Hose Clamp

and Locking Tab

Inlet Hose Connector

Inlet Hose

(NO DIPS IN HOSE)

Transom

2" (51mm)

Minimum

Inlet Strainer

3/8" (10mm)

Thread

Thru-Hull

Connector

or equivalent)