Attwood 4202 Instrukcje instalacji - Strona 3

Przeglądaj online lub pobierz pdf Instrukcje instalacji dla Przełącznik Attwood 4202. Attwood 4202 3 stron. Automatic float switch
Również dla Attwood 4202: Instrukcje instalacji (2 strony)

Drukuj stronę

4. Connect the spliced leads to the "Manual" terminal of the three-way switch.

Important:

Although the switch is submersible, the lead wires must terminate in a

waterproof connection. Mount wires above the highest possible water mark

Heavy Duty Bilge Pump

to prevent electrolysis damage to the boat.

5. With three-way switch on AUTO, test float switch by gently raising the

4030, 4060, 4031, 4061

float. Pump should activate with float up, and deactivate with float down.

See figure 4

Installation Instructions

6. Test pump by ensuring that pump turns on when water level is above float

Attwood marine hardware, navigational lighting, bilge pumps, and other

switch, and shuts off when water level is pumped below float switch. Cycle

marine accessories are specified more than any other brand by America's

the pump with water in the bilge several times to ensure that the system is

best-known boat manufacturers as original equipment. Look to Attwood for

functioning properly.

quality replacement parts and marine accessories.

Figure 5

SAVE THESE INSTRUCTIONS

Form Number 69317 Rev. D

2-Way Switch On/Off

HD 1700: 10 Amp Rating

HD 2000: 12 Amp Rating

Brown Wire

•

HD 1700: 10 Amp Fuse

•

HD 2000: 12 Amp Fuse

Black Wire

WIRING INSTRUCTIONS FOR MANUAL OPERATION

1. Splice suitable lengths of brown and black 16-gauge wire to existing pump

wiring, enough to reach ON/OFF/ switch and battery.

2. Using insulated terminal connectors, connect positive lead (brown) to the

ON/OFF switch. Connect negative lead (black) to ground.

3. In a location easily accessible for changing fuses, splice fuse holder into

positive lead (brown). The fuse holder must be installed within 72" (183 cm)

of the positive (+) battery terminal.

4. To check system, feed water into the pump. If flow appears to be too low,

make sure wires have been connected properly: brown-to-positive (switch),

and black-to-negative.

Figure 6

•

CLEANING INSTRUCTIONS

1. To remove the motor housing from base: Depress the locking button and

twist motor housing counter-clockwise.

2. Remove three retaining screws that attach pump chamber to motor

housing. Remove chamber.

•

Off

•

72" (183mm)

Maximum

Length From (+)

Terminal To

Fuse Holder

•

–

12 Volt Battery

•

Locking Button

•

O-Ring

Pump Chamber

3. Inspect impeller chamber and motor shaft behind impeller. Remove any

foreign objects.

4. Inspect "O" ring on lower chamber for nicks, cuts or other damage. Apply a

light coat of petroleum jelly to "O" ring surface.

5. Assemble chamber into motor housing. Ensure "O" ring is in retaining

groove and alignment pin is in pin receptacle next to locking button.

6. Install and tighten retaining screws.

7. Attach motor housing to pump base by aligning four retaining tabs and

twisting clockwise until lock button snaps into place.

03/10

ATTWOOD HEAVY DUTY BILGE PUMP LIMITED WARRANTY:

ATTWOOD CORPORATION, 1016 North Monroe, Lowell, Michigan 49331,

('Attwood') warrants to the original consumer purchaser that this Attwood

Bilge Pump will be free from defects in materials and workmanship under

normal use and service for:

Recreational/Pleasure Boats — A period of three (3) years from the date of

original consumer purchase.

Commercial Boats — A period of one (1) year from the date of original

consumer purchase.

This warranty does not extend to any batteries or fuses used with the pump.

This limited warranty is not applicable if the bilge pump has been damaged

by accident, improper installation, unreasonable use, lack of proper

maintenance, unauthorized repairs or modifications, or other causes not

arising out of defects in materials or workmanship. Attwood's obligations

under this warranty are limited to repair of the product at Attwood's plant or

replacement of the product at Attwood's option and at Attwood's expense.

Any expenses involved in the removal, reinstallation, or transportation of the

product are not covered by this warranty. The product must be returned to

Attwood's plant at the address indicated above postage prepaid, with proof

of original purchase including date. If Attwood is unable to replace the bilge

pump and repair is not commercially practicable or cannot be timely made, or

if the original consumer purchaser is willing to accept a refund in lieu of repair

Impeller

or replacement, Attwood may refund the purchase price, less an amount for

depreciation. The acceptance by Attwood of any product returned or any

Motor Housing

refund provided by Attwood shall not be deemed an admission that the

product is defective or in violation of any warranty.

THIS WARRANTY IS ATTWOOD'S ONLY EXPRESS WARRANTY OF

THIS PRODUCT. NO IMPLIED WARRANTY SHALL EXTEND BEYOND

ONE (1) YEAR FROM THE DATE OF ORIGINAL CONSUMER PURCHASE.

ATTWOOD SHALL NOT BE LIABLE FOR ANY DAMAGES FOR LOSS OF

USE OF THIS PRODUCT, NOR FOR ANY OTHER INCIDENTAL OR

CONSEQUENTIAL DAMAGES, COSTS OR EXPENSES.

Some states do not allow limitations on how long an implied warranty lasts or

the exclusion or limitation of incidental or consequential damages, so the

above limitations and exclusions may not apply to you. This warranty gives

you specific legal rights and you may have other rights which may vary from

state to state.

1016 N. Monroe Street, Lowell, MI 49331-0260 www.attwoodmarine.com