Atwood MPD 87850 Instrukcja instalacji i obsługi

Przeglądaj online lub pobierz pdf Instrukcja instalacji i obsługi dla Części samochodowe Atwood MPD 87850. Atwood MPD 87850 4 stron. Bolt swivel, retaining ring swivel, tubular swivel, jacks

Drukuj stronę

ENGLISH, FRANCAIS

SAFETY ALERT SYMBOLS

Safety Symbols alerting you to potential personal safety hazards.

Obey all safety messages following these symbols.

WARNING

avoid possible

injury or death

Installer:

Provide these instructions to the consumer.

Consumer: Read and keep documents available for future reference.

INSTALLATION

JACK MAY FALL CAUSING INJURY

Use ONLY Atwood mounting bracket and provided retaining ring with

•

Atwood Retaining Ring Swivel Jacks.

Atwood mounting bracket is designed to ensure proper engagement of

•

the locking pin during use.

Atwood mounting bracket and retaining ring is designed as a system

•

with Atwood jacks to ensure proper snap ring engagement, retention

and lock pin function.

HANDLE MAY INJURE OR DAMAGE PROPERTY

, jack handle must clear all obstructions when in use.

BEFORE INSTALLATION

•

Install jacks in accordance with provided instructions.

•

HAZARDOUS FUMES

Adequate ventilation must be provided when welding.

•

WELDING INSTRUCTION

PREPARE THE METAL

Metal must be completely clean and free from rust or paint before welding. It is

difficult to arc against a dirty surface, but any contaminants will find their way

into the weld and reduce its strength. Light use of an angle grinder or flap

wheel will quickly remove surface rust and paint. For more inaccessible areas

an air grinder or dremmel can b e effective.

- 5/32˝ fillet weld minimum.

OR STICK

•

- Use A.W.S. ER 70S-3 or 6 wire or equivalent with a

WELDING

•

diameter of .035 - .045. The recommended shielding gas mixture is

75% - 95% Argon & 25% - 5% CO

- Use E6011 A.W.S. welding rod or equivalent with a

STICK WELDING

•

diameter as follows: 1/8" electrode set power between 115-130 Amps

DC or 5/32" electrode set power between 140-160 Amps DC.

(et Canada)

CAUTION

avoid possible

injury and/or property damage

WARNING

CAUTION

LITERATURE NUMBER

RETAINING RING SWIVEL

•Installation •Operation •Maintenance

RETAINING RING SWIVEL JACKS

Instructions are for single lock pin swivel jacks.

CHOOSE THE CORRECT MOUNTING BRACKET

• type of jack

• size of trailer frame

• type of jack installation

SINGLE LOCK PIN JACK

USE MOUNTING BRACKET

87501 87502 P/N's used only for Series 8---- Atwood Jacks

MPD 87501 - Weld on bracket, fits most frames

MPD 87502 - Bolt on bracket, fits frames 2˝ or 3˝ wide and 3˝, 4˝ or 5˝ deep

Bracket Mounting:

Install Atwood mounting bracket as shown (

1. WELD-ON BRACKET

a. Following

WELDING INSTRUCTIONS

welding along both sides of bracket from top to bottom.

2. BOLT-ON BRACKET around frame

a. Locate mounting plate against frame.

b. Put furnished bolts through holes that are above and below frame.

c. Assemble backing plates to bolts.

d. Put on lock washer, then nuts.

e. Torque nuts to 25-30 ft. lbs.

JACK MAY FALL CAUSING INJURY

• Retaining Ring must be installed in accordance with provided instruc-

tions.

• Do not over expand the retaining ring.

Jack Mounting:

1. Place jack on bracket (

2. Attach the retaining ring (

a. Use Truarc

External Ring Pliers No. 0609 or equivalent snap

ring pliers to expand the retaining ring just enough to slide it

over the groove in the bracket.

b. When the retaining ring is directly over the groove, release the

pliers and allow the ring to retract completely into the groove as

shown in

FIG

c. Obtain Truarc

External Ring Pliers No. 0609 from:

Needed only for Series 8---- Atwood Jacks

Truarc

Company LLC

70 East Willow St.

Millburn, NJ 07041 USA

3. Inspect the ring.

a. Ring must be completely in the groove and a firm fit

b. To test for proper installation, attempt to rotate the ring. It

should require force to cause it to rotate in the groove. It should

not spin freely. Outer diameter of ring installed in groove should

be 2.724˝ diameter maximum (

To Disassemble:

1. Remove retaining ring using Truarc

equivalent snap ring pliers (see Jack Mounting).

2. Use caution when removing the jack.

3. Use new retaining ring when reinstalling the jack on the bracket.

MPD 87850

BOLT SWIVEL

TUBULAR SWIVEL

JACKS

Effective 12/10/07

SEE ILLUSTRATIONS

: (

)

FIG

1).

FIG

,weld bracket to side of frame by

WARNING

1).

FIG

2-A & B) to the bracket.

FIG

Telephone: (800)526-7055

website: www.truarc.com

3).

FIG

External Ring Pliers No. 0609 or

FIG