3onedata IES6300PRO Series Instrukcja szybkiej instalacji - Strona 3

Przeglądaj online lub pobierz pdf Instrukcja szybkiej instalacji dla Przełącznik 3onedata IES6300PRO Series. 3onedata IES6300PRO Series 5 stron. Layer 2 managed industrial ethernet switch

Drukuj stronę

DC device: Model I, Model II, Model IV, Model V



Model I, Model II, Model IV and Model V

provides 6-pin 5.08mm pitch power supply

terminal blocks and power supply occupies

the left 4 pins. It provides two independent

DC power supply systems, P1 and P2. The power input

supports 1 power supply alone or 2 power supply at the same

time; When two power supply input at the same time, it

supports redundant backup of power supply. If one power

supply fails, the device can still work normally without

interruption. Power supply supports anti-reverse connection,

which cannot power the device but won't damage it when it's

reversely connected. The definitions of power pin are shown

in the left figure, and the power supply input is as follows:

Model I, IV: 24/48VDC (12~55VDC).



Model II, V: 48VDC (PoE: 44~55VDC).



AC device: Model III, Model VI



Model III and VI provide 6-pin 5.08mm

pitch terminal blocks (the power supply

occupies the left 4 pins) and 1 AC power

supply system. The definitions of power pin are shown in the

left figure, and the power input range is 110/220VAC

(85~256VAC/DC).

【Relay Connection】

This series device provides 6-pin 5.08mm

pitch terminal blocks, RELAY occupies the

right 2 pins. Relay terminals are a set of

normally open contacts of the device alarm

relay. They are open circuit in the state of

normal non alarm, closed when any alarm information occurs.

For example, they are closed when powered off, and send out

alarm. The relay supports the output of DC power supply

alarm or network abnormality alarm. It can be connected to

alarm light or alarm buzzer or other switching value collecting

devices, which can timely inform operators when the alarm

occurs.

【I/O Port Connection】

This series device provides 8-pin 3.81mm pitch terminal

blocks and 2 DI and 2 DO. This device

can detect I/O input status, and operators

can set the conditions of alarm status.

When the I/O input status meets the set alarm conditions, the

I/O output alarm would be triggered. The pin definitions of I/ O

port are shown as follows:

Definition

DI1+, DI1-

DI digital signal input channel 1

DI2+, DI2-

DI digital signal input channel 2

DO1+, DO1-

DO digital signal output channel 1

DO2+, DO2-

DO digital signal output channel 2

【USB Interface】

This

series

devices

Type-A(Female) interface. The USB interface can be

connected to a USB flash drive to download logs and

configuration files, or upload configuration files. For specific

operations, please refer to the appendix of the user manual.

【DIP Switch Settings】

The series of devices provide 4-bits DIP switch

for function setting, where "ON" is enable valid

terminal. The definitions of DIP switch are as

follows:

DIP

Definition

Operation

Restore

Set the DIP switch to ON, the

Factory

device will root automatically

Settings

and restore to factory settings,

then turn off the DIP switch.

2-4

Reserved

—

【Console Port Connection】

The series of device provides 1 program

debugging port based on RS-232 serial port

which

can

conduct

management after connecting to PC. The interface adopts

RJ45 port, the RJ45 pin definition as follows:

Pin No.

Definition

TXD

RXD

【LED Digital Tube】

This series of device provides a 1 7-segment LED

digital tube to display the running status of the device,

which is convenient for maintenance and understanding of the

working status of the products. The corresponding status is

shown in the following table.

LED digital tube

status

provides

USB2.0

device

CLI

command

GND

Note