Auber Instruments JSL-72 Instrukcja obsługi

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Timer Auber Instruments JSL-72. Auber Instruments JSL-72 3 stron. Timer for coffee grinder
Również dla Auber Instruments JSL-72: Instrukcja obsługi (3 strony)

Drukuj stronę

AUBER INSTRUMENTS

JSL-72 Instruction Manual

1. Overview

This JSL-72 timer is specifically designed for controlling coffee grinder.

It can count from 0.01" to 99.99" or from 1" to 99'59". Counting direction

can be set by user(counting up or counting down). Accumulated time/

cups can be automatically stored in the timer and reset by user.

Operating function modes include single dose, double dose and

manual. Most function features can be activated by front key pad or

remote switch. However, manual function can only be accessed

through remote switch. Three different display modes can be

programmed. User can shift among single/double dose display mode,

total running time display mode, and total number of cups display

mode. Timer adjust function can be deactivated to prevent any

accidental change.

2. Specification

Timer range: 0.01" to 99.99". Or 1" to 99'59"

Timer mode: single dose, double dose, manual

Timer trigger: power on, front key pad, or remote switch

Timer accuracy: <1s/day.

Power supply: 90-260V AC or DC.

Power consumption: <2W

Relay output:7A@240VAC,10@120VAC and 24VDC

Relay life: 100,000 times.

Operating temperature: 0-60 °C.

Humidity: 0-95%RH

Panel cutout: 44.5x44.5mm

Outer dimension: 48x48x85 mm.

3. Front Panel

Figure1. Front panel

1. Time range indicators: M for minutes, S for seconds. Both will be

illuminated when the time base is M:S(Minutes : Seconds)

2. Timer indicators: T1 is illuminated for single dose, T2 is

illuminated for double dose.

3. OUT indicator: illuminated when relay is on; turns off when relay

is off.

4. SET key. When timer is not running, in single/double dose

display mode, press it will shift between single dose time (T1) and

double dose time (T2)(see section 5.1 for details); press and hold it

for 3 seconds will shift between single/double dose display mode

and total running time/cups display mode(see section 5.1 for

details); press and hold it for 5 seconds will enter the parameter

programming menu(see section 5.2 for details).

2012.11

JSL-72 Timer for Coffee Grinder

Version 1.2

5. Down key: When timer is not running, in single/double dose display

mode, press it will lower the time setting value; in total running time/

cups display mode, hold it for 4 seconds will reset the value.

When timer is running, in either display mode, press it will stop the

timer. In programming mode, press it will go to the next programming

value.

6. Up key: When timer is not running, in single/double dose display

mode, press it will increase the time setting value. When timer is

running, press it will stop the timer. In programming mode, press it will

go to the previous programming value.

7. RST key: Reset key. When timer is not running, press it will activate

the timer. When timer is running, press it will stop the timer.

8. LED digital display. In single/double dose display mode, the top

displays the actual time; the bottom displays the set value. In total

running time/cups modes, the top displays the accumulated running

time/cups; the bottom displays tot/CuPS. In programming mode, the

top displays setting parameters; the bottom displays programming

value.

4. Terminal Assignment

Figure 2. Terminal assignment

Terminal functions when timer is running:

Manual(MAN),T2 (double dose time), T1(single dose time),

Common(COM).

Connecting MAN and COM: Timer starts running when they are

connected.

Connecting T2 and COM: Timer starts running for T2 when they are

disconnected .

Connecting T1 and COM: Timer starts running for T1 when they are

disconnected.

5. Programming

When timer is not running, press SET key for 5 seconds to enter the

programming menu. For each parameter setting, use up/down key to

select different programming values. Press SET key to confirm and

move on to next parameter. See figure 3 on next page for the

procedure. For the definition of each programming value, see

following section.

WWW.AUBERINS.COM

P1/4