3onedata TNS5500-4GT-8POE Instrukcja szybkiej instalacji - Strona 2
Przeglądaj online lub pobierz pdf Instrukcja szybkiej instalacji dla Przełącznik 3onedata TNS5500-4GT-8POE. 3onedata TNS5500-4GT-8POE 4 stron. Managed rack-mounted industrial ethernet switch
Drukuj stronę
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running;
please don't directly contact to avoid scalding.
【Rack-mounting the Device】
Step 1
Select the device installation location to reserve
sufficient size.
Step 2
Adopt screws to install the mounting lugs in the
device position as figure below.
Step 3
Place the device in the rack; adopt 4 screws to
install the mounting lugs on the left and right side in
the rack.
Step 4
Check and confirm the product is firmly installed on
the rack, then mounting ends.
【Rack-mounting Device Disassembling】
Step 1
Power off the device.
Step 2
Unscrew the fixing screw of mounting lug on the
rack.
Step 3
Remove the device from the rack, disassembling
ends.
Note:
Power ON operation: first connect power line to the
connection terminal of device power supply, then power
on.
Power OFF operation: first unpin the power plug, then
remove the power line, please note the operation order
above.
【Power Supply Connection】
The series devices provide 3-pin 5.08mm
pitch power supply terminal blocks. Power
supply range: 110VAC/DC
(100-240VAC/DC).
【Relay Connection】
This device provides 3-pin 5.08mm pitch relay terminal blocks.
Relay terminal blocks is a pair of normally
open contacts of device alarm relay. They
are open circuit in normal non alarm state,
closed when any alarm information occurs. Such as: it's
closed when power off, and send out alarm. This series
switches support 1 channel relay alarm information output,
support DC power alarm information or network abnormal
alarm output, it can be connected to alerting lamp, alarm
buzzer, or other switching value collecting devices for timely
warning operating staffs when alarm information occurs.
【Communication Interface Connection】
M12 100M Copper Port
This device provides 8 10/100Base-T(X) ports. The interface
type is M12 D-Coded 4-pin slot (female). The pin
definitions of M12 are as follows:
No.
Definition
Description
1
TD+
100M Ethernet transmitted signal
Positive
2
TD-
100M Ethernet transmitted signal
Negative
3
RD+
100M Ethernet received signal
Positive
4
RD-
100M Ethernet received signal
Negative
M12 Gigabit Copper Port
This
device
10/100/1000Base-T(X)
interface type is M12 A-Coded 8-Pin slot
(female) and its pin definitions are as
follows:
No.
Definition
Description
1
D0+ (DA+)
The first group of bi-directional
data of Gigabit Ethernet
positive
2
D0- (DA-)
The first group of bi-directional
data of Gigabit Ethernet
negative
3
D1+ (DB+)
The second group of
bi-directional data of Gigabit
Ethernet positive
4
D1- (DB-)
The second group of
bi-directional data of Gigabit
Ethernet negative
5
D3+ (DD+)
The fourth group of
bi-directional data of Gigabit
Ethernet positive
6
D3- (DD-)
The fourth group of
bi-directional data of Gigabit
Ethernet negative
7
D2- (DC-)
The third group of
bi-directional data of Gigabit
Ethernet negative
8
D2+ (DC+)
The third group of
bi-directional data of Gigabit
Ethernet positive
【Console Port Connection】
This device provides 1 program debugging port based on
provides
4
interfaces.
The