CON-TEC TL-328 E-Stop Podręcznik użytkownika - Strona 7
Przeglądaj online lub pobierz pdf Podręcznik użytkownika dla Akcesoria rowerowe CON-TEC TL-328 E-Stop. CON-TEC TL-328 E-Stop 8 stron. Dynamo led rear light
Drukuj stronę
User manual
dynamo LED rear light
TL-328 E-Stop
Congratulations on the purchase of your new device. The user's manual is part of this device and
contains important information to safety, installation and disposal. Familiarize yourself with all
operating and safety instructions before using the device. Use the device as described and in the
specified areas of application. Keep this manual in a safe place and have it with you when using
the device.
Used symbols
Green Point – Recycling the packaging
Symbol for the detection of electrical and electronic devices
Test mark of the Federal Motor Transport Authority
K XXXX
(K with the following approval number)
Proper use
The product is intended for use on bicycles with pedal assistance and serves the illumination of the
road. This LED front light is approved according to the currently valid RTLR (StVZO). The product is
intended for outdoor use.
Note:
The light should only be installed on bikes with pedal assistance that meets one of the following
conditions. If after unloading-conditioned disconnection of the drive assistance still an uninterrupted
electricity supply of the lighting system is guaranteed for at least two hours or the drive assistance
can be used as an alternator transitional to continue to provide the lighting system with power.
WARNING! LIFE AND ACCIDENT HAZARD FOR INFANTS AND CHILDREN!
Never leave children unattended with the packaging material, because of suffocation danger by
swallowing packaging parts. Always keep the device away from children. The device is not a toy!
This device can be used by children of age 8 and over and by persons with reduced physical or
mental capabilities or lack of experience and knowledge if they have been supervised or instructed
concerning the safe use of the device and by understanding resulting hazards. Children are not
allowed to play with the device. Cleaning and user maintenance should not be carried out by children
without supervision. Do not disassemble the device. Improper repairs can cause significant risks for
the user. Only have repairing made by qualified personnel.
Manual_TL-328 E-Stop_2019-02 DE-03
Safety information
- Do not look into light.
- The tail light must be mounted and adjusted that the reference axis is parallel to the vehicle's
median longitudinal plane and parallel to the road surface.
- The light distribution may be obscured by no other attached parts or pieces of luggage, not even
partially.
- The LEDs are not interchangeable. If the LED fails, the entire luminaire must be replaced.
LED rear light and rear reflector
1
2
3
4
5
6
Mapped components
1
Rear light
2
2 LED rear light
4 LED stop indicator function
3
4
Integrated rear reflector
5
Mounting screws
6
Push & pull plug for dynamo and front light connection
LED rear light assembly
Mount the rear light (1) to the carrier. Use the included screws and nuts.
Connection to the E-bike system
The sliding shoe
6
to connect to light to the E-bike system is located at the back of the rear light
Pull the slliding shoe
6
completely out until the two holes are aligned. Insert the uninsulated cable
ends into the contacts according to the polarity through the sliding shoe
6
back again. As a result, the free cable ends are trapped.
Black cable = power
Black-white cable = earth
Rear light adjustment
Attention:
Regularly check the correct setting and mounting height of your rear light. The rear light must be
mounted in a range from 250 to 1200 mm above the ground. It must be mounted and adjusted so
that the reference axis is parallel to the vehicle longitudinal mid-plane and parallel to the road surface
(see figure).
Operation
The tail light is switched on and off via the e-bike system. Check regularly for proper function. A
setting or a „programming" is not necessary for the brake indicator function. It is automatically active
with the connection to the dynamo (or headlight). In case of a negative acceleration 2 LEDs of the
brake indicator function are additionally activated for approx. 3 seconds, so that 4 LEDs shine, while
the brake indicator function is active.
Attention: The brake indicator function is not a brake light.
1
.
6
and push the sliding shoe