3onedata TNS5800 Series Instrukcja szybkiej instalacji - Strona 4
Przeglądaj online lub pobierz pdf Instrukcja szybkiej instalacji dla Przełącznik 3onedata TNS5800 Series. 3onedata TNS5800 Series 5 stron. Layer 3 rack-mounted industrial ethernet switch
Również dla 3onedata TNS5800 Series: Instrukcja szybkiej instalacji (4 strony), Instrukcja szybkiej instalacji (4 strony), Instrukcja szybkiej instalacji (3 strony), Instrukcja szybkiej instalacji (4 strony)
Drukuj stronę
【Logging in to WEB Interface】
Support WEB management and configuration. Computer can
access the device via Ethernet interface. The way of logging
in to device's configuration interface via IE browser is shown
as below:
Configure the IP addresses of computer and the
device to the same network segment, and the
network between them can be mutually accessed.
Enter device's IP address in the address bar of the
computer browser.
Enter device's username and password in the login
window as shown below.
Click "Login" button to login to the WEB interface of
the device.
Note:
The default IP address of the device is "192.168.1.254".
The default username and password of the device are
"admin123".
If the username or password is lost, user can restore it to
factory settings via management software; all modified
configurations will be cleared after restoring to factory
settings, so please backup configuration file in advance.
Please refer to user manual for specific configuration
method of logging in to WEB interface and other
configurations about network management function.
【Specification】
Panel
Gigabit PoE M12
10/100/1000Base-T(X),
(Female),
automatic
full/half
MDI/MDI-X
maximum capacity of a single
port is 30W PoE power supply
output. Pin 1 and 2 of PoE
power supply are positive, while
pin 3 and 4 are negative
Gigabit M12
10/100/1000Base-T(X),
M12(Female), 8-Pin X-Coded,
Automatic Flow Control, Full/half
Duplex
Autotunning; support two groups
of Bypass
100M PoE M12
10/100base-T(X),
(Female),
automatic flow control, full/half
duplex
automatic detection; The single
port supports up to 30W PoE
power supply output. Pin 1 and
3 of PoE power supply are
positive, while pin 2 and 4 are
negative
Console port
CLI command line management
port (RS-232), RJ45
Alarm port
M12
Indicator
8-Pin
X-Coded,
flow
rate
control,
duplex
mode,
Switch Property
autotunning;
The
Backplane bandwidth
cache size
MAC address table
Power Supply
Model I, Model II
Mode,
MDI/MDI-X
M12
4-Pin
D-Coded,
Model III, Model V
mode,
MDI/MDI-X
8-pin 5.08mm pitch terminal
blocks (relay occupies 2 pins) or
7-pin Male M23 port (relay
occupies 2 pins) , support 1
relay
alarm
output,
current
loading capacity is 1A@30VDC
or 0.3A@125VAC
Power indicator, alarm indicator,
running
indicator,
interface
indicator, PoE indicator
128G
12Mbit
16K
Power
input:
110VDC(66~156VDC),
dual
power
supply
redundancy,
support
anti-reverse
connection
protection
Connection method: 8-pin
5.08mm
pitch
terminal
blocks
(includes
6-pin
power supply)
Power input: 110VDC, dual
power supply redundancy,
support
anti-reverse
connection
Connection method: 7-PIN
Male
M23
interface
(includes
4-pin
power
supply)