Dan D'Agostino Momentum Instrukcja obsługi - Strona 3
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Wzmacniacz Dan D'Agostino Momentum. Dan D'Agostino Momentum 11 stron. Hd preamplifier
Również dla Dan D'Agostino Momentum: Instrukcja obsługi (13 strony), Instrukcja obsługi (13 strony), Instrukcja obsługi (10 strony), Instrukcja obsługi (15 strony), Instrukcja obsługi (11 strony)
Drukuj stronęLEGAL NOTIFICATIONS
Dan D'Agostino Master Audio Systems is a registered trademark of Dan D'Agostino Master Audio
Systems, LLC. The information in this owner's manual is subject to change without notice. Current
Version 1.0 of this manual was produced by the Dan Dan D'Agostino Master Audio Systems, LLC
engineering, sales and marketing departments.
The information in this manual is the sole property of Dan D'Agostino Master Audio Systems, LLC.
Any reproduction in whole or part without the expressed written permission of Dan D'Agostino Master
Audio Systems, LLC is prohibited. No material herein may be transmitted in any way including either
electronic or mechanical methods for any purpose without the expressed written permission of Dan
D'Agostino Master Audio Systems, LLC.
PACKAGE CONTENTS
If any of the following items are missing, please contact your dealer:
1 Momentum HD Preamplifier
1 Momentum Preamplifier power supply
(Both encased in protective static-cling
vinyl. Please keep for future shipping)
1 remote control
4 cone feet
CAUTION:
NO USER SERVICEABLE PARTS INSIDE. Do not open the amplifier's chassis or
remove any of its screws. Contact Dan D'Agostino Master Audio Systems, LLC or your dealer if
you have service needs.
WARNING:
Do not expose this preamplifier to moisture or excessive humidity, and do not
use it outdoors. Fire hazard may result.
The lightning flash with arrowhead, within an equilateral triangle, is intended
to alert the user to the presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude to constitute a risk of
electrical shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating maintenance (servicing) instructions in the
literature accompanying the appliance.
1 AC power cord
1 antenna
1 power supply cable
1 owner's manual
1 pair of white lifting gloves
1 microfiber cleaning cloth
UNPACKING AND INSTALLATION
Unpacking the Momentum HD Preamplifier from the Pelican case
While the preamplifier is still in its case, please move it to a location near the place where it will
be installed. Remove all jewelry including watches, rings and belts from your person to avoid
damage to the exterior of the preamplifier during the removal and installation. Gloves
are provided.
The finish of the Momentum HD Preamplifier is extremely delicate. To maintain the preamplifier's
pristine surface, we suggest wearing the supplied white gloves when handling the preamp
to avoid abrasion, fingerprints caused by oils from the skin, etc. Please refer to OPERATION:
Maintenance for instructions on cleaning.
Installation requirements
The Momentum's dense metal chassis makes it much heavier than the average preamplifier, so make
sure the surface that will support the Momentum HD Preamplifier can safely hold its weight.
Adequate ventilation must be provided for the preamplifier. There should be at least 3 inches of
clearance on each side of the preamplifier and 3 inches of clearance at the top, and the bottom
vents must not be obstructed by thick carpet, dust, etc. We recommend that the preamplifier
be installed in an open equipment rack to ensure proper ventilation. The preamplifier may be
installed in a closed cabinet or in an equipment closet, but the cabinet or closet must be designed
with substantial ventilation at top and bottom; active ventilation (i.e., powered fans) is preferred.
Do not place the preamplifier directly on a carpeted floor.
Do not plug the Momentum HD Preamplifier or any other Dan D'Agostino Master Audio Systems
product into a power strip or power conditioner.
The Momentum HD Preamplifier is designed with special cone feet that screw into the bottom
of the preamplifier chassis and match up with indentations on the top of the power supply. The
bottom of the power supply has soft feet designed to isolate the preamplifier assembly from
vibration. (These feet will not stain or mar the surface underneath them.)
To attach the cone feet, use two people to turn the preamplifier chassis upside down and place it
on a soft but secure surface—a few towels draped over a sturdy table, for example. Screw the feet
all the way into the threaded holes on the bottom of the chassis. Now place the power supply in
the place where you want to install the Momentum HD Preamplifier. Use two people to turn the
preamplifier back over again. Place it carefully atop the power supply chassis, lining up the points
of the cone feet with the indentations on the top of the power supply.