Dan D'Agostino Monoblock amplifier Instrukcja obsługi - Strona 3

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Wzmacniacz Dan D'Agostino Monoblock amplifier. Dan D'Agostino Monoblock amplifier 9 stron. Progression monoblock amplifier

Drukuj stronę

CAUTION:

NO USER SERVICEABLE PARTS INSIDE. Do not open the amplifier's chassis or

remove any of its screws. Contact Dan D'Agostino Master Audio Systems or your dealer if you

have service needs.

WARNING:

Do not expose this amplifier to moisture or excessive humidity, and do not use

it outdoors. Fire hazard may result.

The lightning flash with arrowhead, within an equilateral triangle, is intended

to alert the user to the presence of uninsulated "dangerous voltage" within the

product's enclosure that may be of sufficient magnitude to constitute a risk of

electrical shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user

to the presence of important operating maintenance (servicing) instructions in the

literature accompanying the appliance.

LEGAL NOTIFICATIONS

Dan D'Agostino Master Audio Systems is a registered trademark of Dan D'Agostino Master

Audio Systems. The information in this owner's manual is subject to change without notice.

Current Version 1.1 of this manual was produced by the Dan D'Agostino Master Audio Systems

engineering, sales and marketing departments.

The information in this manual is the sole property of Dan D'Agostino Master Audio Systems.

Any reproduction in whole or part without the expressed written permission of Dan D'Agostino

Master Audio Systems is prohibited. No material herein may be transmitted in any way including

either electronic or mechanical methods for any purpose without expressed written permission

of Dan D'Agostino Master Audio Systems.

PACKAGE CONTENTS

Package contents

If any of the following items are missing, please contact your dealer:

1 Progression monoblock amplifier encased in protective packaging

1 owner's manual

1 pair of white lifting gloves

1 microfiber cleaning cloth

1 AC power cord

UNPACKING AND INSTALLATION

Unpacking the Progression monoblock amplifier from the shipping box

Two adults are recommended for lifting the nearly 125-pound amplifier from the shipping box.

Position the shipping box so that one person stands at the front of the amplifier and one person

stands at the back of the amplifier. Both people need to grab a pair of the cardboard handle

cutouts (one pair located at the front of the amplifier and one pair located at the back of the

amplifier) and simultaneously lift the amplifier straight up, out of the carton. Bend and lift with

your knees, not your back. Please move it to a location near the place where it will be installed

and remove the outer foam blocks and protective plastic covering. We recommend you remove

all jewelry including watches, rings and belts from your person to avoid damage to the exterior of

the amplifier during the removal and installation.

Installation requirements

The surface that will support the Progression monoblock amplifier must be capable of safely holding

the nearly 125-pound weight of each amplifier.

Adequate ventilation must be provided for the amplifier. There should be at least 3 inches of

clearance on each side of the amplifier and 3 inches of clearance at the top, and the bottom vents

of the amplifier must not be obstructed by thick carpet, dust, etc. We recommend that the amplifier

be installed in an open equipment rack or on amplifier stands to assure proper ventilation. The

amplifier may be installed in a closed cabinet or in an equipment closet, but the cabinet or closet must

be designed with substantial ventilation at top and bottom; active ventilation (i.e., powered fans) is

preferred. Do not place the amplifier directly on a carpeted floor.

For best possible sound quality and maximum output, we recommend you connect each pair of

Progression monoblock amplifiers to a dedicated 15-amp outlet.

If you need to return the amplifier for service

If you should need to send the Progression monoblock amplifier back to us for service, be sure

to use the original box and materials for shipment.

Before you ship the amplifier, unplug it from the wall and let it cool down for 6 hours. To protect

the finish during shipping, return the amplifier to its original plastic shipping wrap. Make sure the

amp is completely cool and has not been plugged in for 6 hours before you do this. Wrapping

the amplifier when it is warm will cause the plastic to leech into the amplifier's surface and will

permanently damage the finish.