Abt Powerline SC1-8 Instrukcja obsługi produktu - Strona 11
Przeglądaj online lub pobierz pdf Instrukcja obsługi produktu dla Akcesoria do kamer Abt Powerline SC1-8. Abt Powerline SC1-8 15 stron. Valve-regulated sealed lead acid battery
the ambient temperature. When the temperature is
higher, the charging voltage should be lower and
conversely when the temperature is lower, the
charging voltage should be higher. For specific
recommendations, please refer to the section on
Temperature Compensation. Similarly, charged
volume (measured in ampere hours) realized over a
given time will vary in direct relation to the ambient
temperature; the higher the ambient temperature,
the higher the charged volume in a given period of
time and the lower the ambient temperature, the
lower the charged volume in the same given period
of time. Figure 20 shows the relationship between
charged volume and temperature.
Figure 20. Charging characteristics at
different temperatures
0.1CA-6.825V(13.65V)CONSTANT
(%) (xCA) (V)
120
7.00
100
6.50
0.1
80
0.08
60
6.00
0.06
40
5.50
0.04
20
0.02
0
0
15
20
10
0
5
CHARGING TIME (HOUSE)
Initial Charge Current Limit
A discharged battery will accept a high charging
current at the initial stage of charging. High
charging current can cause abnormal internal
heating which may damage the battery. Therefore,
when applying a suitable voltage to recharge a
battery that is being used in a recycling application it
is necessary to limit the charging current to a value
of 0.30C Amps(max.). However, in float/standby use,
Powerline SC are designed so that even if the
available charging current is higher than the
recommended limit, they will not accept more than
2C Amps and the charging current will fall to a
relatively small value in a very brief period of time.
Normally, therefore, in the majority of float/standby
applications no current limit is required. Figure 21
shows current acceptance in Powerline SC charged
at a constant voltage of 2.30 Vpc without
current limit.
When designing a charger, it is recommended that
suitable circuitry is employed to prevent damage to
the charger caused by short circuiting the charger
output or connecting it in reverse polarity to the
battery. The use of current limiting and heat sensing
circuits fitted within the charger are normally
sufficient for the purpose.
VOLTAGE CHARGING
(V)
14.0
13.0
12.0
o
o
AT 0 C(32 F)
o
o
AT 20 C(68 F)
11.0
o
o
AT 40 C(104 F)
CHARGING CURRENT
35
25
30
40
Figure21. Constant voltage charge
characteristics with no
current limit
(xCA)
2.0
CHARGE VOLTAGE:2.30V/C
TEMPERATURE:20 C (68 F)
1.5
1.0
0.5
8
0
2
4
6
10
CHARGING TIME (SECONDS)
Charge Output Regulation and Accuracy
To ensure the correct voltage is set accurately, when
adjusting the output voltage of a constant voltage
charger, all adjustments must be made with the
charger "ON LOAD" Adjusting the output voltage with
the charger in an"OFF LOAD" condition may result in
undercharging. The constant voltage range required
by a battery is always defined as the voltage range
applied to a battery which is fully charged. Therefore,
a charger having the output characteristics illustrated
in Figure 22, should be adjusted with the output
voltage based on point A. The most important factor in
adjusting charger output voltage is the accuracy at
point A, which should be in the range of
2.275vpc
0.005 volts per cell; however this accuracy
is not normally required over the entire range of the
load. A charger adjusted in accordance with Figure 22
will never damage a battery, even if the charger has the
characteristics Shown by the broken line in Figure 22.
Figure 22. Output voltage adjustment
CHARGING CHARACTERISTICS
A
CHARGING TIME
Temperature Compensation
As the temperature rises, electrochemical activity in a
battery increases and conversely decreases as
temperature falls. Therefore, as the temperature
rises, the charging voltage should be reduced to
prevent overcharge and increased, as the
temperature falls, to avoid undercharge. In general,
in order to attain optimum service life, the use of a
temperature compensated charger is recommended.
The recommended compensation factor for Powerline
o
SC is -3mV/ C/Cell (for float/standby) and -4mV / C
/Cell (cyclic use). The standard centre point for
temperature compensation is 20 C. Figure 23 shows
the relationship between temperatures and charging
voltages in both cyclic and float/standby applications.
o
o
20
30
40
50
60
OUTPUT CHARACTERISTICS
OUTPUT CURRENT
A
o
o
09