ADDER AdderLink XDIP Skrócona instrukcja obsługi - Strona 2
Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla Przedłużacz ADDER AdderLink XDIP. ADDER AdderLink XDIP 2 stron.
Drukuj stronę
START HERE: Using the screen, keyboard and mouse connected to
a node that will be a receiver, you should see the Welcome screen:
Welcome
Please choose your language and keyboard layout.
English
gb
OK
00:0F:58:02:DF:3B C1.00.00
|
1 If necessary, change the language and keyboard layout. Click OK:
SETUP - Receiver or Transmitter?
Is this node a receiver or transmitter? After restoring to defaults
you can change this in the future.
RECEIVER
TRANSMITTER
2 Click the RECEIVER option to make this node a receiver:
SETUP - Basic Information
Enter the names, descriptions and admin password for this
receiver.
Receiver Name
Receiver 1
Description
Receiver Description
Local Computer
Computer Name
Description
Computer Description
New Admin Password
Password for Node Configuration
Confirm Admin Password
Password for Node Configuration
Cancel
OK
3 Enter the details for this receiver, including the password (required
for admin access to the configuration details). Click OK.
Web:
Contact:
Support:
© 2017 Adder Technology Limited • All trademarks are acknowledged.
Part No. MAN-QS-XDIP-ADDER_V1.1
You will now see a list of all discovered XDIP nodes. If an entry
shows SoL (Start of Life) then it is unconfigured (that node's PWR
indicator will also show red). Otherwise, any configured XDIP
transmitter node will show TX:
#
Name
Transmitter 1
TX
AdderLink XDIP 02DF3B
SoL
Notes
• If you are adding several nodes at once and need to identify a
particular node, click the icon to flash the front panel indicators of
the chosen node in the list.
• If nodes have been added since displaying the list, click the icon to
refresh the list.
• Passwords can be left blank, but this is not recommended.
4 Click an entry marked SoL to configure it as a transmitter:
5 Enter the details for this transmitter, including two separate
passwords: one for admin configuration purposes and the other to
restrict user access to this transmitter. Click OK.
www.adder.com
Warranty
Adder Technology Ltd warrants that this product shall be free from defects in workmanship and materials for a period of two years from the date
www.adder.com/contact-details
of original purchase. If the product should fail to operate correctly in normal use during the warranty period, Adder will replace or repair it free
of charge. No liability can be accepted for damage due to misuse or circumstances outside Adder's control. Also Adder will not be responsible for
www.adder.com/support
any loss, damage or injury arising directly or indirectly from the use of this product. Adder's total liability under the terms of this warranty shall in
all circumstances be limited to the replacement value of this product. If any difficulty is experienced in the installation or use of this product that
you are unable to resolve, please contact your supplier.
SETUP - Channel Selection
Select which nodes to add as channels.'SoL' marks nodes that are
yet to be configured and 'TX' denotes available transmitters.
Description
Description
Description
BACK
NEXT
SETUP - Basic Information
Enter the name, description, and admin and access password for
this transmitter.
Transmitter Name
Transmitter 2
Description
Transmitter Description
New Admin Password
Password for Node Configuration
Confirm Admin Password
Password for Node Configuration
New Access Password
Password for User Access
Confirm Access Password
Password for User Access
Cancel
OK
The discovered nodes will be again listed, showing any changes you
have made to the name(s) and description(s):
SETUP - Channel Selection
Select which nodes to add as channels.'SoL' marks nodes that are
yet to be configured and 'TX' denotes available transmitters.
#
Name
Description
1
Transmitter 1
Description
Transmitter 2
Description
TX
BACK
6 Repeat steps 4 and 5 for each listed SoL node.
7 Ensure that all the transmitters (8 maximum), to which you wish
to connect from this receiver, show a number in the left hand
column. If an entry shows TX, it is yet to be connected. Click on
the entry to connect it with this receiver; if a password is set on
the transmitter, you will be asked to enter it. Once successfully
connected, the TX for the entry will change to a number.
8 When all transmitters have been connected, click NEXT.
9 You can now optionally change the order of transmitters in the
channel list. Click, hold and drag an entry to the required slot:
SETUP - Customise the Channel Order
Drag and drop the channels into your preferred order.
#
Name
Description
1
Transmitter 1
Description
2
Transmitter 2
Description
3
4
5
6
7
8
BACK
10 When all transmitters are in the required order, click DONE.
11 The receiver will now show the Channel List (see the rear page).
From here you can choose between a local computer (if
connected to your receiver) or any of the associated transmitters.
NEXT
DONE