AirVac AVP12000 Instrukcje instalacji - Strona 2

Przeglądaj online lub pobierz pdf Instrukcje instalacji dla Odkurzacz AirVac AVP12000. AirVac AVP12000 2 stron.

Drukuj stronę

Overhead Vacuum Duct Installation (continued)

6 Secure the inlet valve to the valve bracket with the two

wall plate screws.

7 Repeat steps for each wall inlet valve location.

Under the Floor Installation

In homes with a pier and beam foundation or basement,

either the overhead or an under the floor installation can

be made. Sometimes under the floor installation is easier

in an existing home, especially if the roof has a low pitch

and clearances in the attic adds to the installation problem.

Under the floor installation also eliminates encountering

fire blocks in the wall. Shorter risers are also utilized,

eliminating the longer tube drop from the attic.

1 Vacuum tubing should be secured to floor joist with

perforated nailing strips or tube straps.

2 Generally, follow the overhead installation steps, but

from below the floor, to install each wall inlet valve.

Alternate Vacuum Duct Riser Installation

An effective technique highly suitable for many types

of construction with adequate working room inside the

attic is to make drops to the wall inlet valves through the

ceiling, then route the tube through the wall at inlet level

for the inlet valve on the opposite side of the wall. If this

method is used, the drop from the inside of the attic for the

riser can be made in the corner of a closet, utility room,

etc. where the tubing is not visible or not objectionable

to the Homeowner. On occasion this might be the only

alternative for placing an inlet valve in a desired location.

3 Power Unit Installation

Power Unit Unpacking and Pre-assembly

This AirVac power unit is packaged disassembled in a nested configuration which reduces the size of the shipping

carton and allows for much smaller shelf space requirements than previous AirVac models. The power unit must

be assembled during installation.

1 Carefully remove the nested vacuum from the box.

2 Separate each of the nested parts and place them

gently on the floor.

3 Refer to the parts identification figure below to

familiarize yourself with each of the parts.

VACUUM PARTS IDENTIFICATION

EXHAUST MUFFLER

EXHAUST ELBOW

INLET PLUG

MOUNTING

SCREWS

VACUUM BODY

BRACKET

CAUTION

Do not mount the motor head onto the vacuum

body until AFTER the vacuum body is hung on

the mounting bracket. Placing the motor head

on the vacuum body before mounting causes

the unit to be top heavy and may tip the vacuum

over, causing damage to the vacuum.

4 Connect the 90° steel exhaust elbow to the motor

head. The exhaust elbow can point to the left, right or

vertical depending on the installation requirements.

Secure the exhaust elbow to the motor head flange

with the #4 self‑tapping screw.

5 PLATINUM SERIES ONLY: Install the dust cone inside

the bottom end of the vacuum body as shown in the

figure. Be sure the cone snaps against the large ridge in

the vacuum body. DO NOT PUSH DUST CONE PAST

THE LARGE RIDGE!

6 PLATINUM SERIES ONLY: Install the slide‑gate collar

dust bag into the debris bucket. BE SURE TO FULLY

EXPAND THE BAG WITH YOUR HAND TO FILL THE

BUCKET.

Power Unit Mounting

1 Determine the mounting location for the power unit. Be

sure clearance dimensions are followed. The power

supply cord length is 5 feet. An AC power outlet of the

proper type on a dedicated circuit breaker must be

available within 5 feet so the power supply cord can be

directly plugged into the electrical outlet. DO NOT USE

AN EXTENSION CORD.

2 Use a stud finder to locate a wall stud for attaching the

mounting bracket. Mark the stud location.

3 Attach the mounting bracket to the wall, centered on the

marked stud, with the bottom edge 40" above the floor,

using the two 1/4" x 2" lag screws and a 7/16" socket.

4 Carefully hang the vacuum body by sliding the body's

mounting tab into the mounting bracket slot.

5 Fit the motor head onto the vacuum body with the

controls facing forward latching the two locking snaps.

6 Hang the debris bucket on the two bucket slide latches.

Swing the two slide latch handles up to lock the debris

bucket into place.

7 Slide the exhaust muffler onto the exhaust elbow.

Optional Exhaust Tubing

The vacuum's exhaust can be piped away from the

power unit if desired or required. The exhaust tubing

must vent to the outside of the house, NOT INTO THE

ATTIC. A louvered exhaust vent cap (VM136) is available

to terminate the exhaust tubing. Steel tubing is also

available for the exhaust tubing and may be required by

local building codes.

CAUTION

In order to avoid motor failure resulting from

excessive back pressure, DO NOT install more

than 30 feet of exhaust tubing and DO NOT

install any bends in the exhaust tubing closer

than 18" from the exhaust muffler.

1 Install any optional exhaust tubing following the

guidance above.

2 Connect the optional exhaust tubing to the muffler.

UNDER FLOOR INSTALLATION

INSTALL

VALVE BRACKET

12" TO 15" ABOVE

FLOOR LEVEL

PLATE

FLOOR

VM106

SWEEP TEE

FLOOR

JOIST

ALTERNATE DUCT RISER INSTALLATION

THE TUBING DROP

CAN BE INSIDE A CLOSET

TO WALL VALVE

THEN THROUGH THE

ON OTHER SIDE

WALL TO THE WALL

OF THE WALL

VALVE INSIDE THE ROOM

SLIDE-GATE COLLAR BAG

FLEXIBLE HOSE

(PLATINUM SERIES ONLY)

HOSE

CLAMPS

LAG

DUST CONE

DEBRIS BUCKET

(PLATINUM SERIES ONLY)

EXHAUST ELBOW & DUST CONE INSTALLATION

ATTACH THE EXHAUST

ELBOW TO THE MOTOR

HEAD WITH #4 SCREW

DO NOT PRESS

CONE PAST THE

LARGE RIDGE

EXHAUST ELBOW

CAN POINT TO

LEFT, RIGHT OR VERTICAL

DUST BAG INSTALLATION (PLATINUM SERIES ONLY)

EXPAND THE DUST

BAG BEFORE PLACING

IT INTO THE DEBRIS BUCKET

PLACE BAG'S

SLIDE-GATE

HERE

SLIDE-GATE COLLAR BAG

HANGING THE MOUNTING BRACKET & MOUNTING THE VACUUM BODY

ATTACH MOUNTING BRACKET

TO WALL WITH TWO LAG SCREWS

SCREW TO

WALL STUD

BOTTOM

EDGE 40"

ABOVE

FLOOR

INSTALLING THE MOTOR HEAD AND DEBRIS BUCKET

SNAP MOTOR HEAD

ONTO VACUUM BODY

RETAINING

SNAP

HANG DEBRIS

BUCKET ON BUCKET

SLIDE LATCHES

OPTIONAL EXHAUST TUBING

18" MINIMUM FROM

THE MUFFLER BEFORE

ANY BENDS IN THE

EXHAUST TUBING

MUST VENT OUTSIDE

OF THE HOUSE

VM136

LOUVERED

EXHAUST

VENT CAP

Vacuum Intake Connection

Depending on the requirements of the installation, the

STUD

main vacuum duct line can be connected to the left or

right side intake port of the power unit.

1 Cut a 4" piece of duct tubing.

2 Slide the tubing piece into the left or right power unit

intake port. DO NOT CEMENT TUBING.

3 Slide a hose clamp onto the flexible hose. Slide the

flexible hose onto the tubing piece. Tighten the hose

clamp.

FLOW

4 Slide another hose clamp onto the flexible hose.

Connect the flexible hose to the drop from the main

MAIN VACUUM TUBE

vacuum duct system line. Tighten the hose clamp.

5 The unused power unit intake port MUST be sealed,

slide the inlet plug onto the unused intake port.

4 Power Unit Electrical

Low Voltage Control Wire Connection

1 Strip back the insulation about 1/2" from the two‑

HOLE IN

conductor low voltage control wire cable at the power

CEILING

unit.

2 Using a small screwdriver or other object, press down

RISER AND

CONTROL

on one of the wire locks on the control wire connector

WIRE

(top rear of motor head) while inserting the wire

into the connector hole. Release the wire lock while

holding the wire in. Repeat with the other wire and the

other hole. Polarity is not important, either wire can be

connected to either hole.

Grounding Instructions

This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of least

resistance for electrical current to reduce the risk of electrical shock. This appliance is equipped with a cord having

an equipment‑grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that

is properly installed and grounded in accordance with all local codes and ordinances.

WARNING

Improper connection of the equipment-grounding

conductor can result in risk of electric shock.

Check with a qualified electrician or service

person if you are in doubt as to whether the

outlet is properly grounded. Do not modify the

plug provided with the appliance - if it will not

fit the outlet, have a proper outlet installed by a

qualified electrician.

Power Connection

1 BE SURE THE UNIT'S POWER SWITCH IS OFF.

Plug the line cord into the AC receptacle.

2 Verify that power is available to the vacuum by

MOTOR HEAD

switching the unit's power on then off.

System Testing

TIP DUST CONE

The AirVac central vacuum system should be tested for good suction throughout the system. Use a vacuum gauge

INTO VACUUM BODY

(VM181) at each wall inlet valve location to measure the vacuum suction.

BOTTOM END

PRESS DUST CONE

5 Troubleshooting

IN UNTIL THE FOUR

TABS SNAP AGAINST

THE LARGE RIDGE

NOTE: NO USER SERVICEABLE PARTS INSIDE, DO NOT LUBRICATE MOTOR.

IF THE MOTOR FAILS TO OPERATE

1 Be sure the power unit is plugged into a working AC outlet.

2 Push breaker reset button on the power unit.

3 Check the panel circuit breaker that connects the power unit.

AFTER CHANGING OF THE BAG (PLATINUM SERIES ONLY)

1 Push down the RESET button for 7 seconds to reset the bag indicator.

IN CASE OF LOW VACUUM POWER

PLACE THE BAG INTO THE

1 Be sure that the inlet plug is inserted into the unused power unit intake port.

DEBRIS BUCKET AND

2 Check that all wall valves are closed.

EXPAND THE BAG AGAINST

THE DEBRIS BUCKET SIDES

3 Check that all gaskets on wall valves are sealed.

4 Check to see if debris bucket or bag (Platinum Series only) needs emptying.

5 Check for obstructions in the hose, tools, or vacuum lines.

6 Check for any ruptures or breaks in the vacuum duct system.

If you are unable to resolve the operational problems, please contact AirVac technical support at (800) 421‑1587.

6 Limited Warranty

Linear LLC warrants AirVac Platinum Series power units to be free of defects for

10 years, and AirVac Red Series power units to be free of defects for 5 years.

The warranty period begins from either (1) the date of "first user" purchase of

this product or (2) the first close of escrow date on a residence in which this

new product was originally installed. This warranty extends to the original user

HANG VACUUM BODY ON

of the product and to each subsequent owner of the product during the term of

MOUNTING BRACKET

this warranty. Linear LLC will repair or replace, at its option, parts and materials

at no charge. Parts supplied under this warranty may be new or rebuilt at the

option of Linear LLC.

If, during the limited warranty period, it appears as though this product contains

a defect which is covered by this limited warranty, call our toll free service

number before dismantling the product (1-800-421-1587). Remember to

attain a Return Product Authorization number (RPA) before returning any

product to Linear LLC. Send this product freight pre-paid and insured

to our service center for warranty repair. You will be advised on shipping

instructions when you call the toll free service number. Linear LLC will return

the repaired product freight pre‑paid within the U.S.A. The installing dealer or

distributor may assist you, at your choice and expense, with returning product

for repair. Please include a brief description of the problem and a dated proof‑

of‑purchase receipt with any product that is returned for warranty repair. ANY

PRODUCT RETURNED WITHOUT A RETURN PRODUCT AUTHORIZATION

NUMBER WILL BE REFUSED.

BUCKET

SLIDE

LATCH

SWING THE TWO

BUCKET SLIDE

LATCHES UP

OUTSIDE

WALL

VACUUM INTAKE CONNECTION

VACUUM

INTAKE PORT

HOSE

CLAMPS

LOW VOLTAGE CONTROL WIRE CONNECTION

LOW VOLTAGE

CONTROL WIRE

CONNECTOR

CAUTION

All circuit breakers must be SEPARATE and

DEDICATED as with any other major appliance.

The electrical outlets MUST match the plug

WITHOUT THE USE OF ADAPTERS. DO NOT USE

AN EXTENSION CORD.

AC POWER CONNECTION

BE SURE THE POWER

SWITCH IS OFF

THIS LIMITED WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES,

EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR

OTHERWISE, AND OF ANY OTHER OBLIGATIONS OR LIABILITY ON THE

SELLER'S PART. THIS LIMITED WARRANTY DOES NOT COVER DAMAGE

CAUSED BY ACTS OF GOD, IMPROPER INSTALLATION, NORMAL

SYSTEM WEAR AND TEAR AS DEFINED BY THE MANUFACTURER, THE

VIOLATION OF APPLICABLE BUILDING OR ELECTRICAL CODES, OR

THE USE OF NON-AIRVAC WIRE, CABLE, OR WALL HOUSINGS. THIS

LIMITED WARRANTY APPLIES ONLY TO PRODUCTS INSTALLED IN A

PRIVATE RESIDENCE.

UNDER NO CIRCUMSTANCES SHALL THE SELLER BE LIABLE FOR

CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES ARISING IN

CONNECTION WITH USE, OR INABILITY TO USE THIS PRODUCT. IN

NO EVENT SHALL SELLER'S LIABILITY, FOR BREACH OF WARRANTY,

BREACH OF CONTRACT, NEGLIGENCE, OR STRICT LIABILITY, EXCEED

THE COST OF THE PRODUCT COVERED HEREBY. NO PERSON

IS AUTHORIZED TO ASSUME FOR US ANY OTHER LIABILITY IN

CONNECTION WITH THE SALE OF THIS PRODUCT.

Some states do not allow the exclusion or limitation of consequential, incidental

or special damages, so the above limitation or exclusion may not apply to you.

This limited warranty gives you specific legal rights, and you may also have

other rights which vary from state to state.

www.purelypowerful.com

Manufactured by:

USA & Canada (800) 421-1587 & (800) 392-0123

(760) 438-7000 - Toll Free FAX (800) 468-1340

www.linearcorp.com

THE UNUSED

INTAKE PORT

MUST BE SEALED!

FLEXIBLE

HOSE

MAIN

INSERT THE INLET

VACUUM

PLUG ONTO THE

TUBE

UNUSED VACUUM

INTAKE PORT

LOW VOLTAGE

CONTROL WIRE

FROM WALL VALVES

PUSH EACH WIRE

LOCK DOWN WHILE

INSERTING THE WIRE

INTO THE CONECTOR

HOLE

PLUG THE POWER UNIT

INTO A GROUNDED

AC OUTLET THAT IS

WIRED TO A DEDICATED

CIRCUIT BREAKER

DO NOT USE AN

EXTENSION CORD

OR AN AC ADAPTER!

226529 B