addi Express Kingsize Instrukcja obsługi - Strona 14

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Maszyna do szycia addi Express Kingsize. addi Express Kingsize 16 stron.
Również dla addi Express Kingsize: Podręcznik (20 strony)

Drukuj stronę
addi Express Kingsize Instrukcja obsługi
1 /
2 /
3 /
4 /
5 /
6 /
1 /
2 /
3 /
8

Introduction to Plain knitting

43 needles are used
1 / Make sure that the operating switch is up. Pull
some of the yarn off the ball and through the middle
of the addiExpress until it touches the table.
2 / Now turn the handle backwards and start with
the first white needle to the left of the black needles.
(The black needles are not used for plain knitting)
3 / Start turning the handle slowly clockwise, while
doing this alternate the position of the yarn from in
front of to behind of the rising needle. This is done
until you reach the first black needle.
4 / When you come to the first black needle, the
yarn runs outward. Follow the steps 5 to 6 of the
chapter "circular knitting". (The loop of the first
black needle goes off later and can be hidden by just
pulling it tight.)
5 / The difference to round knitting is that you turn
the handle forwards and backwards. Each end of a
row will be shown by a stop of the winding. Always
turn the handle until it stops.
6 / In order to cast off follow the steps 8 to 10 of
circular knitting.

addiStopper

1 / The addiStopper allows you determine individual
web widths in a quick and clean style.
2 / Use: Place the stopper to the left of the black
needles, 2 needles from where you wish to begin
(to do this, first turn the handle till you reach the
desired white needle and position the first stopper).
Place the second stopper 4 needles beyond where
you wish to end. When turning the handle, make
sure the edge stitches are picked up properly!
3 / Example: To knit 10 stitches straight up, use
needles 6 to 21. To do so, position the first stopper
(start stopper) between needles 5 and 6. Position the
second stopper (end stopper) between needles 21
and 22.
1 /
2 /
3 /
4 /
5 /
6 /

Multi-coloured knitting/version 1

Tying yarns together
1 / To knit with more than one colour, just tie the
two yarns together. Be careful to make a proper, tight
knot.
2 / Lay the ends of both yarns, one behind the other,
in a cross.
3 / Place your left thumb on the point where the
yarns cross.
4 / Then make a loop with the thread in your right
hand around its own end.
5 / Now take the end of the other colour. Lay it over
the right-hand thread of the loop and pull it through
under the left-hand thread.
6 / Remove your thumb from the loop and pull the
knot really tight. Cut the yarn end off near the knot.
When knitting it in, position the knot in such a way
that it does not sit on a needle.
Multi-coloured knitting/version 2
Crossing yarns
With this version, neater joins are generally
achieved.
At the end of a row or round, the ball that was being
used is removed from the yarn guide and placed in
the centre of the machine.
The ball with the new colour is introduced into the
thread guide and knitting continues in the normal
manner for machine knitting.
For recurring strips, such as the ones on the waste-
paper bin (see page 38) and the striped cardigan (see
page 58), the two balls are interlaced once after each
turn (= 2 rows) so that no loose threads remain on the
side - as in hand knitting.
Upon completion of the piece of knitting, that is after
casting off, it is recommended to tie the free-hanging
threads together and then to sew them up.
9