Dancing Wings Hobby 0.8 Tiger Moth Instrukcja obsługi - Strona 3
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Zabawka Dancing Wings Hobby 0.8 Tiger Moth. Dancing Wings Hobby 0.8 Tiger Moth 6 stron.
Drukuj stronę02-4
在此处的预留槽内插入纸合页。
Insert the paper hinges into
the reserved slot here.
02-5
Epoxy glue
把垂直尾翼插入机身，用环氧胶粘固。
Insert the vertical tail into the fuselage,and glue firmly with
epoxy glue.
03
机翼安装
Install the Wing
03-1
在下机翼的舵机孔处安装舵机，把舵机线从机翼末端导出。此处可能需要
舵机延长线。左右机翼相同安装。
Install the servo into the servo hole of the lower wing,lead the
servo wire from the end of the wing.A servo extension cable may
be required here. Same installation for left and right wings.
3
在转向舵的底部插入尾轮，并调整角度用CA胶粘固。
Insert the tail wheel at the bottom of the steering rudder,adjust
the angle,and glue firmly with CA glue.
在垂直尾翼的预留槽内插
入纸合页。
Insert the paper hinges
into the reserved slot
on the vertical tail.
02-6
在垂直尾翼上安装转向舵，通过纸合页连接，调整间隙保持舵面可
以自由摆动，连接处用CA胶粘固。
Install the steering rudder on the vertical tail,connect it with
paper hinges,adjust the gap to keep the rudder surface to
swing freely,and fix the connection with CA glue.
03-2
快装接头
EZ-connector
1.从M板上取下舵角，安装到副翼的预留槽内，用CA胶粘固。
Remove the servo horn from the M plate, install it in the
reserved groove of the aileron, and fix it with CA glue.
2.在舵机上安装舵臂，舵臂上安装快装接头。
Install the servo arm on the servo, and install the EZ-connector
on the servo arm.
3.舵机与副翼通过钢丝连杆连接，钢丝连杆Z型一端穿入舵角，另一端
插入快装接头，然后锁紧快装接头螺丝固定钢丝。
Connect the servo and the aileron with a steel wire connecting
rod, one end of the Z-shaped steel wire rod is inserted into the
servo horn, and the other end is inserted into the EZ-connector,
and then tighten the EZ-connector screw to fix the wire.
03-3
注意朝向
Pay attention to the orientation
03-4
注意朝向
Pay attention to the orientation
03-5
碳杆 Carbon rod
Ø6*220mm
碳杆 Carbon rod
Ø3*80mm
03-7
自攻螺丝
Self-tapping screw
M1.5x10mm
在上机翼底面预留槽内插入连接件，注
意朝向，装好后用CA胶粘固。
Insert the connector into the
reserved groove on the bottom
surface of the upper wing, pay
attention to the orientation,fix it
with CA glue after installation.
在下机翼顶面预留槽内插入连接件，
注意朝向，装好后用CA胶粘固。
Insert the connector into the
reserved groove on the bottom
surface of the lower wing, pay
attention to the orientation,fix it
with CA glue after installation.
1.把PVC风挡折叠成左图
形状。
03-6
Fold the PVC
windshield into the
shape shown on the
left.
2.用自功螺丝把风挡固定
到机身上，如下图所示。
Fix the windshield to
the fuselage with
self-tapping screw as
shown in the figure
below.
自攻螺丝
把支架安装到机身，用自功螺丝固定。
Self-tapping screw
Install the bracket to the fuselage
M1.5x10mm
and fix with self-tapping screw.
4