Danfoss 084B8070 Instrukcja obsługi - Strona 11

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Kontroler Danfoss 084B8070. Danfoss 084B8070 14 stron.

Drukuj stronę

Continued

Refrigerant setting:

1=R12. 2=R22. 3=R134a. 4=R502. 5=R717. 6=R13.

7=R13b1. 8=R23. 9=R500. 10=R503. 11=R114.

12=R142b. 13=

User defined.

14=R32. 15=R227.

16=R401A. 17=R507. 18=R402A. 19=R404A. 20=R407C.

21=R407A. 22=R407B. 23=R410A. 24=R170. 25=R290.

26=R600. 27=R600a. 28=R744. 29=R1270. 30=R417A.

31=R422A.

Input signal on DI2. Function:

(0=not used. 1=status on DI2. 2=door function with alarm

when open. 3=door alarm when open. 4=defrost start

(pulse-signal). 5=ext. main switch 6=night operation

7=thermostat band changeover (activate r21). 8=alarm

function when closed. 9=alarm function when open.

10=case cleaning (pulse signal). 11=forced cooling at hot

gas defrost.). 12=night cover, 13=coordinated defrost)

Configuration of light function

: 1=Light follows day /night

operation, 2=Light control via data communication

via 'o39' , 3=Light control with a DI-input, 4=As "2", but

light switch on and night cover will open if the network

cut out for more than 15 minutes.

Activation of light relay (only if o38=2)

Rail heat On time during day operations

Rail heat On time during night operations

Rail heat period time (On time + Off time)

Case cleaning. 0=no case cleaning. 1=Fans only. 2=All

output Off.

Selection of EL diagram. See overview page 2 and 3

Download a set of predetermined settings. See overview

page 8.

Access code 2 (partial access)

Replace the controllers factory settings with the present

settings

Input signal on DI3. Function: (high voltage input)

(0=not used. 1=status on DI2. 2=door function with alarm

when open. 3=door alarm when open. 4=defrost start

(pulse-signal). 5=ext. main switch 6=night operation,

thermostat band changeover (activate r21)

9=Not used.

10=case cleaning (pulse signal). 11=forced

12=night cover. 13=Not used.

cooling at hot gas defrost,

14=Refrigeration stopped (forced closing))

Rail heat control

0=not used, 1=pulse control with timer function (o41

and o42), 2=pulse control with dew point function

Dew point value where the rail heat is minimum

Dew point value where the rail heat is 100% on

Lowest permitted rail heat effect in %

Time delay from "open door" refrigeration is started

Fan operation on stopped refrigeration (forced closing):

no/0=Fan Off, yes/1=Fan On

Definition of readings on lower button:

1=defrost stop temperature, 2=S6 temperature,

3=S5_B temperature

Display of temperature

1= u56 Air temperature

2= u36 product temperature

Light and night blinds defined

0: Light is switch off and night blind is open when the

main switch is off

1: Light and night blind is independent of main switch

Configuration of alarm relay

The alarm relay will be activated upon an alarm signal

from the following groups:

1 - High temperature alarms

2 - Low temperature alarms

4 - Sensor error

8 - Digital input enabled for alarm

16 - Defrosting alarms

32 - Miscellaneous

64 - Injection alarms

The groups that are to activate the alarm relay must be

set by using a numerical value which is the sum of the

groups that must be activated.

(E.g.: a value of 5 will activate all high temperature

alarms and all sensor error.

AK-CC 550A - 084B8070

Code

o30

o37

o38

On=light

o39

o41

o42

o43

***

o46

o61

o62

***

o64

o67

o84

. 8=Not used.

o85

o86

o87

o88

o89

o90

o92

o97

o98

P41

2 3

6 7

Min.

Max.

0/Off

1/On

0 %

100 %

100

0 %

100 %

100

6 min.

60 min.

6 (0)

100

0/Off

1/On

0/Off

-10°C

50°C

-9°C

50°C

0 %

100 %

0 min.

240 min.

0/no

1/yes

0/no

127

111

Fac.

Actual