cashco SA1 Instrukcja instalacji, obsługi i konserwacji - Strona 3
Przeglądaj online lub pobierz pdf Instrukcja instalacji, obsługi i konserwacji dla Kontroler cashco SA1. cashco SA1 12 stron. Ultra high purity, spring loaded pressure reducing regulators
Drukuj stronę
VII.
MAINTENANCE
A. General:
1. The regulator may be serviced without re mov-
ing the regulator from pipeline. The reg u la tor
is designed with quick-change trim to simplify
maintenance.
2. Record the nameplate information to req ui si-
tion spare parts for the regulator. The in for-
ma tion should include: Size, Product Code,
and Serial Number.
3. Refer to Section IX for recommended spare
parts.
Only use original equipment parts
sup plied by Cashco for re build ing or re pair ing
regulators.
4. Owner should refer to owner's procedures for
removal, handling, cleaning and disposal of
nonreusable parts, i.e. seals, etc.
5. The Inner Trim is re moved and replaced in the
body (23) as an assemblage of parts. The
Inner Trim Assembly, here in af ter called ITA,
consists of the fol low ing parts:
Item
Dynamic
No.
Seal Type
13 ..................... All ..........................Piston-Guide Bearing
15 ..................... All ................................ Cage O-ring Seal
16..................... UC.................................................Shim
19 ..................... All ................................................... Cage
20 ..................... All ...........................................Valve Plug
21 ..................... All ............................................ Seat Ring
27 ..................... All ............................. Dynamic Side Seal
27.1 .............. CP............................................. Cap Seal
27.2 .............. CP..........................O-ring Energizer/Seal
27.3 .............. UC .......... U-Cup Seal w/Metal Energizer
6. A detailed view of the dynamic side seal parts
is shown in Figure 1; an assembled ITA in
Figure 2; and a cross-sectional drawing of
the entire regulator is shown in Figure 3.
SYSTEM UNDER PRESSURE. Prior to per form ing
any maintenance, isolate the reg u la tor from the
sys tem and relieve all pressure. Failure to do so
could result in personal injury.
B. Main Regulator Disassembly:
1. Shut down the system in accordance with
Section VI.
2. Loosen adjusting screw lock nut (2) and relax
range spring (6) pressure by turning ad just-
IOM-CA1/SA1
Part Description
WARNING
SECTION VII
3. Loosen the diaphragm flange bolts (12) and
4. Place matchmarks on body (23) and spring
5. Remove the washers (14), spring follower (5)
6. Remove upper diaphragm pressure plate (8).
7. Remove diaphragm(s) (9) and examine to
8. Evenly loosen the three cage cap screws (18)
ing screw (1) CCW (viewed from above) until
removed from spring cham ber (4).
nuts (11) uniformly. Remove all bolting.
chamber (4) flanges. Remove the spring
cham ber (4) by lifting vertically.
and range spring (6).
de ter mine if failed. If diaphragms failed, de-
ter mine if op er at ing con di tions are ex ceed ing
designed pressure or tem per a ture limits.
in single revolution increments. The reg u la tor
con tains a lower return spring (22); the ITA
should rise as the cage cap screws (18) are
backed out evenly. A downward holding force
should be ap plied to the top of the piston-guide
bearing (13) to pre vent the ITA from pop ping
up as the last threads of the cage cap screws
(18) are disengaged. Remove washers (17).
13
19
15
*
27.3
*
16
Type UC - U-Cup
Dynamic Seal
27
*
13
19
15
*
27.1
*
27.2
*
16
20
Type CP - Cap
Dynamic Seal
Figure 1: Dynamic Side Seals
20
3