Danfoss VLT FCM 322 Szybka konfiguracja

Przeglądaj online lub pobierz pdf Szybka konfiguracja dla Napędy DC Danfoss VLT FCM 322. Danfoss VLT FCM 322 2 stron.

Drukuj stronę

02/00

Safety

All operations must be carried out by

appropriately trained personnel.

Use all lifting facilities provided e.g.

both lifting points, if fitted, or single

lifting point, if fitted*.

Vertical lifting - Prevent uncontrolled rotation.

Lift machine - Do not lift other equipment with motor

lifting points only.

Before installation check for fan cover damage,

shaft

damage, foot/mounting damage, and loose

fasteners. Check nameplate details.

Ensure level mounting surface, balanced mounting,

not misaligned.

Gaskets, and/or sealants, and guards must be

correctly fitted.

Correct belt tension.

Please observe derating rules, see Design Guide

*Note: maximum hand lift is 20 kg below shoulder,

but above ground level.

Max. weights:

Frame size 80: 15 kg

Frame size 90 & 100: 30 kg

Frame size 112: 65 kg

The voltage on the FC motor is

dangerous when the motor is

connected

to mains. Incorrect installation of the FC

motor may lead to material damage or

serious injury or it may be fatal.

Consequently, the instructions in this Quick Setup as

well as national and local rules and safety

regulations

must be complied with.

Touching the electrical parts may be fatal, even after

the mains supply has been disconnected.

Wait at least 4 minutes.

Installation must be fused and isolated correctly.

Covers and cable entries must be fitted

What if the motor does not start?

Make sure no parameters have been changed

from initial delivery status (factory setting). Use

the Local Control Panel or serial port to reset to

factory setting.

Make sure no STOP command have been

issued by the optional control panel keyboard

(local stop) Control Panel STOP can only be

restarted by the Control Panel START button.

Remove lid to check the Light Emitting Diodes

visible through a hole in the inside isolation cover

(See the drawing), follow table below.

Warning:

Extreme care must be taken when

operating the unit with open lid.

Green

Y Y Y Y Y ellow

ellow

Red

Green

ellow

Red

LED 302

LED 301

LED 300

LED 302

LED 301

LED 300

OFF

For further information see the design guide and/or PROFIBUS manual.

This Quick Setup gives information on safety and

helps you to get your FCM 300 Series motors

installed and running in factory setting, see fig. 1. For

additional information, please see the Design Guide.

Before you start, please read the safety instructions

on the back of this Quick Setup.

T T T T T ools for installation

ools for installation

1 cross-point screwdriver

1 large screwdriver

1 small screwdriver

Min. 2 glands:

MG.03.F5.02 - VLT is a registered Danfoss trademark

NB!

It is the user's or certified electrician's responsibility

to ensure correct earthing and protection in

accordance with applicable national and local

requirements and standards.

Safety regulations

1. The FC motor must be disconnected from mains if repair

work is to be carried out. Check that the mains supply

has been disconnected and that the necessary time has

passed (4 minutes).

2. Correct protective earthing of the equipment must be

established, the user must be protected against supply

voltage, and the motor must be protected against

overload in accordance with applicable national and local

regulations.

In UL/cUL applications ETR provides class 20, overload

protection in accordance with the NEC

RCD's (ELCB relays), multiple protective earthing or

earthing can be used as extra protection, provided that

local safety regulations are complied with.

In case of an earth fault, a DC content may develop in

fault current.

If RCD's are used, local regulations must be observed.

Relays must be suitable for protection of 3-phase

equipment with a bridge rectifier and for a brief

discharge on power-up.

3. The earth leakage currents are higher than 3.5 mA

(approx. 7 mA). This means that the FC motor requires a

fixed, permanent installation as well as reinforced

protective earthing.

W W W W W ar ar ar ar arning against unintended start

ning against unintended start

1. The motor can be brought to a stop by means of digital

commands, bus commands, or references, while the FC

motor is connected to mains.

If personal safety considerations make it necessary to

ensure that no unintended start occurs, these stop

functions are not sufficient.

2. While parameters are being changed, the motor may

start.

3. A motor that has been stopped may start if faults occur in

the electronics of the FC motor, or if a temporary overload

or a fault in the supply mains or the motor connection

ceases.

Action

)

Apply power (see point

Apply start and r

start and r

start and refer

efer

eference

ence

ence signals , (see figure 1 and point

ence

Apply r r r r r eset

eset signal according to figure 1.

eset

Switch off power until all LED's have turned off. After power on reset signal is

required.

Gland sizes

FCM 305-330

FCM 340-375

1 mains cable

1 control cable

Max. cable cross section

Mains supply cable

Control cable

Serial communication cable

*MG03F502*

175R0129

the

)

3X PG16

1X PG21, 2X PG16

4.0 mm

/10 AWG

1.5 mm

/16 AWG

1.5 mm

/16 AWG