Casio 2587 Instrukcja obsługi - Strona 2
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Oglądaj Casio 2587. Casio 2587 3 stron.
Operation Guide 2406 2583 2587
To set the time and date manually
Important!
The receive indicator remains on the display for about three days after successful
receipt of the time calibration signal. Note that you cannot manually change the time
setting while the receive indicator is on the display.
1. Make sure that the current time zone setting is the time
zone for which you want to set the time and date.
Time setting screen
2. In the Timekeeping Mode, hold down B until the
A
current time starts to flash on the display, which
indicates the time setting screen.
• If you want to change the date setting only without
B
changing the time setting, skip to step 4.
3. Use A (+) and C (–) to change the time setting.
D
C
• If you want to register your time setting without
changing the date setting, press B here to exit the
setting screen.
4. Press D to advance to the date setting screen, which
Date setting screen
is indicated by the date flashing on the display.
A
5. Use A (+) and C (–) to change the date setting.
• Pressing D changes back to the time setting screen
B
in step 2.
6. Press B to exit the setting screen.
D
C
Switching between Standard Time and Daylight Saving Time
The time calibration signal sent from Fort Collins includes Standard Time and Daylight
Saving Time information. If you are in a time zone within North America where
Daylight Saving Time is used, you do not need to make any adjustments to switch
between Standard Time and Daylight Saving Time.
When you are in a time zone outside of North America, you can use the following
procedure to turn on Daylight Saving and advance the current time by one hour, when
necessary.
• Note that not all countries or local areas use Daylight Saving Time.
• If the watch receives a time calibration signal, the time is adjusted in accordance
with the time calibration signal data, regardless of the current DST on/off setting. If
you are in a U.S. area that does not use Daylight Saving Time, you need to use the
procedure under "To specify your time zone" to select the time zone to the west of
the time zone where you are. If you are in the Mountain Time Zone in an area that
does not use Daylight Saving Time, for example, select the Pacific Time Zone during
the Daylight Saving Time period.
To switch between Standard Time and Daylight Saving Time
1. Use D to enter the Time Zone Mode.
2. Hold down B until the current time zone differential
DST indicator
value starts to flash, which indicates the setting screen.
A
3. Press D to display the DST setting screen.
4. Press A or C to toggle between Daylight Saving Time
B
(ON) and Standard Time (OFF).
• The DST indicator is on the display while Daylight
D
C
Saving Time is turned on.
5. Press B to exit the setting screen.
• The Daylight Saving Time setting affects the currently
selected time zone only.
• The Daylight Saving Time setting does not affect UTC.
Timekeeping Mode Screens
You can select one of two different screens for viewing the current time in the
Timekeeping Mode: Home Time and Date screen, or Home Time and UTC (Universal
Time Coordinated) screen. Press B to toggle between the two screen formats.
[Module 2406]
Home Time and Date Screen
Month – Day
Day of week
Press B.
B
Hour : Minutes
Seconds
PM indicator
[Modules 2583, 2587]
Home Time and Date Screen
Month – Day
Day of week
Press B.
B
Hour : Minutes
Seconds
PM indicator
• Changing the Home Time setting also causes UTC to change accordingly. Time
zone and DST ON/OFF settings do not have any affect on the UTC.
Home Time and UTC Screen
UTC
Home Time and UTC Screen
UTC
Alarm
You can set a Daily Alarm that sounds at the same time each day, while it is turned on.
• Alarm settings are available in the Alarm Mode, which you enter by pressing D.
To set the alarm time
1. In the Alarm Mode, hold down B until the alarm time
Alarm on indicator
starts to flash, which indicates the setting screen.
• The alarm turns on, which is indicated by the
ON/OFF status
appearance of ON, whenever you display the alarm
A
setting screen.
2. While the alarm time is flashing, use A (+) and C (–)
B
to change it.
• When setting the alarm, take care to set the time
D
C
correctly as a.m. (no indicator) or p.m. (Module 2406:
PM; Modules 2583, 2587: P).
3. Press B to exit the setting screen.
Alarm time (Hour : Minutes)
Alarm Operation
The alarm sounds at the preset time for about 30 seconds, or until you stop it by
pressing any button.
Important!
An ongoing receive operation (auto or manual) is immediately canceled if an alarm
sounds. If you need to set an alarm time in the range of 1:00 AM to 1:15 AM, we
recommend that you trigger a receive operation manually after the alarm sounds.
To turn the alarm on and off
In the Alarm Mode, press C to turn the alarm on (ON displayed) and off (OFF
displayed).
• The alarm on indicator (Module 2406:
the display in all modes while the alarm is turned on.
Date Alert
The Date Alert Mode helps you to remember an important date. After you set an alert
date (month and day), the watch displays a flashing indicator (Module 2406: TODAY!;
Modules 2583, 2587:
) for 24 hours after that date arrives.
• Note that Date Alert is always on and cannot be turned off. The initial default alert
date is December 24.
To set the alert date
1. Use D to enter the Date Alert Mode.
TODAY indicator
2. Hold down B until the alert date starts to flash, which
indicates the setting screen.
A
3. Use A (+) and C (–) to change the setting.
4. Press B to exit the setting screen.
B
D
C
Alert date
Stopwatch
The stopwatch lets you measure elapsed time, lap times,
SP indicator
split times, and two finishes.
1/100 second
• The display range of the stopwatch is 99 hours,
Seconds
59 minutes, 59.99 seconds.
• The stopwatch measurement operation continues until
A
you stop it or until it reaches 99:59' 59.99" (at which time
B
the display resets to all zeros).
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
D
C
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing D.
Hours
Minutes
To measure elapsed time
1. Press A to start the stopwatch.
2. Press A again to stop the stopwatch.
• You can resume the measurement operation by pressing A.
3. Press C to clear the stopwatch to all zeros.
To measure lap times
1. When the stopwatch display shows all zeros, use C to display the lap time screen
(indicated by LA).
2. Press A to start a time measurement.
3. Press C when you want to freeze the first lap time on the display.
• Though the lap time is frozen on the display, timing of the next lap continues
internally.
4. Press C again to switch back to the ongoing timing of the next lap.
• You can repeat steps 3 and 4 as many times as you want.
5. Press A when you want to stop the lap time measurement.
6. Press C to clear the stopwatch to all zeros.
To measure split times
1. When the stopwatch display shows all zeros, use C to display the split time screen
(indicated by SP).
2. Press A to start a time measurement.
3. Press C when you want to freeze the first split time on the display.
• Though the split time is frozen on the display, timing continues internally.
4. Press C again to switch back to the split time measurement.
• You can repeat steps 3 and 4 as many times as you want.
5. Press A to stop the split time measurement.
6. Press C to clear the stopwatch to all zeros.
To determine the time of 1st and 2nd place finishers
1. When the stopwatch display shows all zeros, press C to display the split time
screen (indicated by SP).
2. Press A to start a time measurement.
3. Press C when the first finisher crosses the finish line.
• This causes the time of the first finisher to be frozen on the display, while elapsed
time measurement continues internally.
4. Press A when the second finisher crosses the finish line.
5. Press C to display the time of the second finisher.
6. Press C to clear the stopwatch to all zeros.
; Modules 2583, 2587:
) is shown on
2