AETOOL AE540Y Podręcznik użytkownika - Strona 2

Przeglądaj online lub pobierz pdf Podręcznik użytkownika dla Elektronarzędzie AETOOL AE540Y. AETOOL AE540Y 2 stron. Constant temperature soldering iron

Drukuj stronę

AE540 Series Constant Temperature

Soldering Iron User Manual

AE540 series constant temperature soldering irons are equipped with high-quality PTC two

core heating element, lead-free iron tip. Adopting the closed loop automatic constant

temperature control technology, this soldering iron has obvious advantages like fast

temperature rise, accurate temperature control, and high reliability. Slim and lightweight,

it's suitable for all kinds of soldering process.

Specification

Item No.

Voltage

Frequency

Power

AE540Y

230Vac

50Hz

40W

AE540G

230Vac

50Hz

40W

AE540Q

230Vac

50Hz

40W

Note: Temperature accuracy ±25℃

Using steps

● Remove the plastic protective cap on the iron tip before using.

● Check whether the voltage to be used is correct.

● Turn on the power and wait for about 30 seconds, then apply some solder on the tip to

prevent oxidation.

● Wait for the temperature to rise and become stable, usually about 50-120 seconds, then

can get started.

● After done using, please clean the iron tip and apply some solder on it to make a protective

layer.

● When it's on power but not in use, do not place the product vertically as it might shorten

the service life. After finish using, be sure to unplug to cut off the power.

Note

This device conforms to the specifications of the EC Declaration of Conformity

with Directives 2014/30/EU, 2014/35/EU an 2011/65/EU(RoHS). Nevertheless,

like all electrical appliances, it must be used appropriately. Never forget the

warning tips and heater can reach high temperature.

● The soldering iron needs to be tested before it leaves the factory,so the

soldering tip may cover a small amount of tin, and the casing will be slightly

yellowing, which is normal.

● The iron will reach high soldering temperature 1-2 minutes after being

plugged in, please use it properly and prevent accidental burns.

● We require users to have basic life knowledge and basic electrical related

operation knowledge before using the product.

● For under age users, please be sure to use the product under the guidance

of professionals or guardians.

When using this product, the soldering pencil/soldering tip can reach

temperature up to 350℃, which may cause burns to the user or cause a

fire due to improper application, so Users shall strictly observe the

following rules:

● Keep this product away from flammable materials.

● Keep the product out of reach of children.

● Do not use this product if you are inexperienced or have no sufficient necessary

knowledge without the guidance.

● Do not use this product in wet environment or with wet hands to avoid electric shock.

● Do not modify this product and its accessories without authorization.

● Please turn off the power when replacing parts, do not resume the use until the

equipment completely cools down.

● Please use the accessories from the original factory when replacing the product parts.

● Make sure to turn off the power switch when the equipment is temporarily stopped

or out of use.

Rating temperature

Temperature stability

350℃

±5℃/±9℉

400℃

±5℃/±9℉

450℃

±5℃/±9℉

Warning

Maintenance

● Before any repairs on the soldering iron, unplug it to cut off the power.

● To change the soldering iron tip,（as following Figure 1-1) unscrew the stainless steel

sleeve on the tip, replace the current tip with a new one, and screw tighten the sleeve back.

● Please use the original spare parts authorized by the factory for replacement.

● This soldering iron complies with relevant safety regulations. Always make sure to have

your soldering tool repaired by a qualified electrician.

Nut

Figure 1-1

The soldering iron tip is designed with electroplating protective layer which can greatly

prolong its service life and shall not be damaged by mechanical adaptation (e.g. polishing,

scraping). Clean the oxide on the surface with wet-water sponge or

brass wool carefully, turn on power and heat it and apply some solder on the tip for

protection. If the iron tip has been deformed or worn-out, please replace it with a new one.

Replacement parts

Tips: 900M-T series tips

Heater: ATETOOL PTC two-core heating element

Warranty terms

● ATETOOL provides one (1) year warranty for this product.

● From the date of purchase, the warranty relates to material and

manufacturing defects, and covers both replacement parts and labour cost.

● The warranty shall be void if damage is due to improper use, or if there's

any alterations by unauthorized persons.

Some 900M series soldering tips

900M-T-I

900M-T-1.2D

900M-T-3.2D

900M-T-0.8C

900M-T-6.4C

(More soldering tips information please contact us)

Shenzhen ATTEN Technology Co., Ltd. Electronic Tools Branch

Address：F5, 1-2 #, Tongfuyu, Aiqun Road, Shiyan Street, Bao'an District, Shenzhen,

518132,P.R.China

Tel：(0755) 23408674 - 802

Support：(0755) 23408704 - 818

URL：www.atten.com.cn( in Chinese )

www.atten.com(in English)

casing

Tip

Heater

casing

Nut

Tip

900M-T-B

900M-T-K

900M-T-1.6D

900M-T-2.4D

900M-T-4.6D

900M-T-6.5D

900M-T-3C

900M-T-5C

CBN300125(A)