Freedom Freedom 200+p Instrukcja obsługi - Strona 7
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Alarm samochodowy Freedom Freedom 200+p. Freedom Freedom 200+p 7 stron.
Drukuj stronęcancel or turn off the Anti-Carjacking Feature - once activated, the transmitter cannot be
used to cancel or turn off the Feature. When programming, at Step #5 in Features
Programming Mode press the transmitter's large button to turn this Feature on or press the
small button to turn this Feature off.
16) Door-Activated Anti-Carjack Protection: (Default OFF) This feature causes the
Anti-Carjacking Feature described previously to be activated by the opening and closing of
the vehicle's door at any time while the ignition switch is "on". This Feature may be used
alone, or in conjunction with the previous Transmitter Activated Anti-Carjacking Feature.
If a door is opened and closed while the ignition switch is "on", the Anti-Carjacking Feature
will engage 53 seconds after the door is closed. The Valet Switch must be pressed within
60 seconds after the door is shut to cancel the Anti-Carjacking Protection Feature. When
programming, at Step #5 in Features Programming Mode press the transmitter's large button
to turn this Feature on or press the small button to turn this Feature off.
Total System Reset: This procedure resets all 16 Programmable Features to factory-
set default positions. The security system's control module must be accessed to perform a
Total System Reset. Once accessed, follow these steps:
1) Locate the small round hole in the lower control module case. Two solder dots will
be visible beneath this opening.
3) To learn the first transmitter code, press the large transmitter button, (which will arm/
disarm/panic the system), until you hear one siren burst and one short siren chirp to
confirm that the code was learned. The Status LED will also start flashing once between
pauses. The other transmitter button functions are automatically learned at this time.
4) To program the second, third or fourth transmitter codes, repeat step 3. As each
transmitter is learned, the long confirmation chirp will be followed by two short chirps
for transmitter number two, three short chirps for transmitter number three, and four
short chirps for transmitter number four. An attempt to add any further transmitter
codes will be ignored. The Status LED will increase the number of flashes between
pauses as each transmitter is learned.
5) Turning off the ignition switch will automatically remove the system from Transmitter
Learning Mode, which is confirmed by two siren bursts.
Second Vehicle Operation: The security system can be armed and disarmed from the
combination of pressing both transmitter buttons at the same time. For two vehicle
operation, encode the first vehicle to arm and disarm from the transmitter's large button; this
system will have normal operation. Encode the same transmitters to arm and disarm the
second vehicle from pressing both transmitter buttons. The second vehicle's system will
operate from both buttons and trunk release will operate from the small transmitter button.
Please note that the second vehicle's system will not have the 3rd Channel output function.
Page - 25
Page - 27
2) Short the two solder dots together. A slotted jeweler's screwdriver works well.
3) Momentarily shorting the solder dots together for about 5 seconds will result in two
siren bursts indicating all 16 Programmable Features are at the factory-set default.
Encoding Transmitters
Up to 4 different transmitters may be programmed into the security system's memory.
When a new transmitter is encoded into the system, all previous transmitter codes will be
deleted. If a third or fourth transmitter is desired, all of the transmitters must be encoded into
system's memory. To program transmitters to operate your system, follow this procedure:
1) Turn "on" the ignition switch.
2) Within 5 seconds of turning "on" the ignition switch, press the Valet Switch 5 times.
Note: The system will respond with a long siren chirp and the Status LED will illuminate
steady, confirming that the system is ready to learn a transmitter code. Turning "off" the
ignition automatically terminates the Transmitter Learning Mode, which will be indicated
by two siren bursts. When the first transmitter code is learned, any and all existing prior
transmitter codes will be erased.
L I M I T E D
L I F E T I M E
Products manufactured and sold by OMEGA RESEARCH & DEVELOPMENT, INC. (the Company),
are warranted to be free from defects in materials and workmanship under normal use. If a product sold by
the Company proves to be defective, the Company will repair or replace it free of charge within the first year
and thereafter all parts to be repaired will be free with only a nominal charge for Omega Research and
Development, Inc.'s labor and return shipping, to the original owner during the lifetime of the car in which
it was originally installed.
All products for warranty repair must be sent postage prepaid to Omega Research & Development, Inc.,
P.O. Box 508, Douglasville, Georgia 30133, with bill of sale or other dated proof of purchase. This warranty
is nontransferable and does not apply to any product damaged by accident, physical or electrical misuse or
abuse, improper installation, alteration, any use contrary to its intended function, unauthorized service, fire,
flood, lightning, or other acts of God.
This warranty limits the Company's liability to the repair or replacement of the product. The Company
shall not be responsible for removal and/or reinstallation charges, damage to or theft of the vehicle or its
contents, or any incidental or consequential damages caused by any failure or alleged failure of the product
to function properly. Under No Circumstances Should This Warranty, Or The Product Covered By It, Be
Construed As A Guarantee Or Insurance Policy Against Loss. The Company neither assumes nor authorizes
any person or organization to make any Warranties or assume any liability in connection with the sale,
installation, or use of this product.
This device complies with FCC Rules part 15. Operation is subject to the following two conditions,
(1) This device may not cause harmful interference and, (2) This device must accept any interference
that may be received, including interference that may cause undesired operation.
The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user's authority to operate the
equipment.
Page - 26
W A R R A N T Y
MO_FREEDOM-200+PVER2