Belimo AF24-SR US Instrukcja montażu i obsługi - Strona 2
Przeglądaj online lub pobierz pdf Instrukcja montażu i obsługi dla Jednostka sterująca Belimo AF24-SR US. Belimo AF24-SR US 2 stron. Proportional damper actuator
Drukuj stronęAccessories
AV 10-18
Shaft extension
IND-AF2
Damper position indicator
K4 US
Universal clamp for 3/8" to 3/4" shafts
K4-1 US
Universal clamp for up to 1.05" dia jackshafts
K4-H
Universal clamp for hexshafts 3/8" to 5/8"
KH-AF
Crankarm for up to 3/4" round shaft (Series 2)
KH-AF-1
Crankarm for up to 1.05" jackshaft (Series 2)
KH-AFV
V-bolt kit for KH-AF and KH-AF-1
Tool-06
8mm and 10 mm wrench
SGA24
Min. and/or man. positioner in NEMA 4 housing
SGF24
Min. and/or man. positioner for flush panel mounting
ZG-R01
500
resistor for 4 to 20 mA control signal
ZG-HTR
Thermostat/Heater Kit
ZDB-AF2 US
Angle of rotation limiter
ZG-100
Universal mounting bracket
ZG-101
Universal mounting bracket
ZG-102
Multiple actuator mounting bracket
ZG-103
Universal mounting bracket
ZG-104
Universal mounting bracket
ZG-106
Mounting bracket for Honeywell
new crankarm type installations
ZG-107
Mounting bracket for Honeywell
Series 100 replacement or new crankarm type installations
ZG-108
Mounting bracket for Barber Colman
®
Honeywell
Mod III or IV or Johnson
replacement or new crankarm type installations
ZG-AF US
Crankarm adaptor kit for AF/NF
ZG-AF108
Crankarm adaptor kit for AF/NF
ZS-100
Weather shield (metal)
ZS-150
Weather shield (polycarbonate)
ZS-260
Explosion-proof housing
ZS-300
NEMA 4X housing
NOTE: When using AF24-SR US actuators, only use accessories listed on this page.
For Actuator Wiring Information and Diagrams, Please See Belimo Wiring Guide (pg 349).
Typical Specification
Spring return control damper actuators shall be direct coupled type which
require no crankarm and linkage and be capable of direct mounting to a jackshaft
up to a 1.05" diameter. The actuator must provide proportional damper control in
response to a 2 to 10 VDC or, with the addition of a 500
control input from an electronic controller or positioner. The actuators must be
designed so that they may be used for either clockwise or counterclockwise fail-
safe operation. Actuators shall have control direction of rotation switch
accessible on its cover. Actuators shall use a brushless DC motor controlled by a
microprocessor and be protected from overload at all angles of rotation. Run
time shall be constant, and independent of torque. A 2 to 10 VDC feedback signal
shall be provided for position feedback or master-slave applications. Actuators
shall be UL Approved and CSA certified, have a 5 year warranty, and be
manufactured under ISO 9001 International Quality Control Standards. Actuators
shall be as manufactured by Belimo.
800-543-9038 USA
24 V for 2 to 10 VDC and 4 to 20 mA Control Signal. Output Signal of 2 to 10 VDC for Position Indication.
®
Mod IV replacement or
®
Mod III or Johnson
®
®
MA 3../4..,
®
Series 100
resistor, a 4 to 20 mA
866-805-7089 CANADA
Proportional Damper Actuator, Spring Return Fail-Safe,
Wiring Diagrams
Provide overload protection and disconnect as required.
1
CAUTION Equipment damage!
2
Actuators may be connected in parallel.
Power consumption and input impedance must be observed.
Actuators may also be powered by 24 VDC.
3
Only connect common to neg. (–) leg of control circuits.
5
The ZG-R01 500
resistor converts the 4 to 20 mA control signal to
2 to 10 VDC, up to 2 actuators may be connected in parallel.
WARNING Live Electrical Components!
During installation, testing, servicing and troubleshooting of this product, it maybe
necessary to work with live electrical components. Have a qualified licensed electrician
or other individual who has been properly trained in handling live electrical components
perform these tasks. Failure to follow all electrical safety precautions when exposed to live
electrical components could result in death or serious injury.
24 VAC Transformer
1
Line
Volts
(–)
Control Signal
(+)
2 to 10 VDC
2 to 10 VDC control
4 to 20 mA control
203-791-8396 LATIN AMERICA
AF24-SR US
1 Common
3
2 + Hot
3 Y Input,
2 to 10V
5 U Output
2 to 10V
AF24-SR US
2
23