Addonics Technologies CipherChain CCMSPC2 Podręcznik

Przeglądaj online lub pobierz pdf Podręcznik dla Sprzęt komputerowy Addonics Technologies CipherChain CCMSPC2. Addonics Technologies CipherChain CCMSPC2 1 stron.

Drukuj stronę

Single CipherChain (CCMSPC1)

Device SATA port

(Connect to SATA device)

4-pin floppy

power connection

Reset switch

HDD LED

Dual CipherChain (CCMSPC2)

1. For two SATA devices

Host SATA port 1

(Connect to 1

SATA host)

Device SATA port 1

(Connect to 1

SATA device)

2. For daisy-chaining to increase encryption security

Device SATA port

(Connect to SATA device)

Note: The cipher keys for the two CipherChains can be of same or

different code.

Disable reset switch jumper – By default, CipherChain reset switch is

enabled. To disable reset, remove the jumper. Disabling the reset switch

is recommended if the CipherChain is connected to a boot drive or non-

hotswap SATA controller card.

Reset switch – Under certain applications, the RESET button enables

the adding and removing of hard drives without restarting the system.

Following is an example of such an application:

When the CipherChain is connecting a removable drive system to a

SATA port that supports hot swap, the drive can be removed without

powering off the computer. However the drive icon will still be there

as the system does not realize a hard drive is removed from the

system. In addition, the key code still resides inside the

ADDONICS TECHNOLOGIES

Model: CCMSPC1 & CCMSPC2

Host SATA port (blue color)

(Connect to SATA host)

Disable reset

switch jumper

Power LED

Cipher keyhole

Device SATA port 2

(Connect to 2

device)

Host SATA port 2 (blue color)

(Connect to 2

SATA host)

Host SATA port (blue color)

(Connect to SATA host)

CipherChain. Resetting will turn off the CipherChain, clear the key

code and remove the drive icon. We recommend resetting the

CipherChain whenever a hard drive is removed from a system to

ensure better security.

Likewise when a new hard drive is added to a removable drive

system. The CipherChain can be initialized again by pressing the

RESET button while with the Cipher key inserted. Note that if the

new hard drive is not encrypted or the Cipher key does not match

what is on the encrypted hard drive, it will show up as an

unallocated drive under the drive management screen and no drive

icon will show up in My Computer folder. So it is very important to

make sure that the correct Cipher key is used on the hard drive.

Proceeding to initialize the hard drive will erase all the data

beyond any possibility of recovery.

Green Power LED: In order to turn on the power to the CipherChain, the

cipher key must be inserted prior to power on the system or resetting the

CipherChain. If the power LED does not light up, the system will not

detect the hard drive connected to the CipherChain.

Yellow Power LED: Lights up when there is drive activity.

SATA

Basic Hardware Installation

Mount the CipherChain into the SCSI-1 (Centronics 50-pin) slot on

the PC case. If there is no available SCSI-1 slot, use the PCI

bracket provided and mount the CipherChain on the PCI slot.

Using the provided floppy Y-power cable connect the CipherChain

4-pin floppy power connector to the system's power supply.

Connect the SATA hard drive or storage device to the Device SATA

port on the CipherChain using a SATA cable. Remember to connect

power to the storage device.

Connect the Host SATA port (port with Blue color) on the

CipherChain to the onboard SATA port of the motherboard or an

add-in SATA controller card using a SATA cable.

How to operate the CipherChain:

Note: Hot swapping refers to the ability to plug and unplug the component

without rebooting.

Insert the AES 256-bit cipher key into the cipher keyhole on the

CipherChain.

For SATA port that supports hotswap.

Power on the CipherChain and SATA storage device at the

same time or turn on storage device first before the CipherChain.

For SATA port that does not support hotswap.

Power on the CipherChain and SATA storage device at the

same time.

Observed that the green Power LED should light up. If it does not,

re-insert the cipher key and re-power the devices or reset the

CipherChain.

For new drive, go to the operating system's management utility to

partition, format and mount the encrypted drive.

Go to File Manager and view the encrypted drive.

Note: You may remove the cipher key from the CipherChain once

the CipherChain is powered on. All the files being transferred into

the drive are still encrypted even if the cipher key is removed.

Best Practices:



Create a label to identify the SATA storage device and the Cipher

key used to encrypt the device.



Always keep a spare master key in a safe place.

For additional information about the CipherChain, refer to the

CipherChain manual on the CD or download a copy from

www.addonics.com

TECHNICAL SUPPORT

Phone:

Hours:

Email:

408-453-6212

8:30 am - 6:00 pm PST

http://www.addonics.com/support/query/