Daspi MAXIM 24 Instrukcja obsługi - Strona 7

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Otwieracz do bram Daspi MAXIM 24. Daspi MAXIM 24 15 stron. Weight from 400 kg - 600 kg to 800 kg

Drukuj stronę

INSTALLATION

Important

safety

installation.

Warning: incorrect installation can lead to

severe injury. Follow all the instructions.

To operate a good installation of the gear motor

MAX follow these instructions:

Locate inside the property the correct point to

install MAX, usually near to the support column of

the gate.

Build up a cement emplacement with sizes like

1, foreseeing the passing of the protective

coverings "G" for the passing of the power supply

and control system cables.

Fix, on the surface in cement and perpendicularly

to the gate, the supports "Ps" respecting the

indicated measures

(fig.

Put the plate "Pb" on the supports "Ps" and induct

the protective coverings "G" through the holes "F"

(fig.

2).

Fix the plate "Pb" on the supports "Ps" by the

screws "Vp", and pay attention that the plate "Pb" is

perfectly horizontal

(fig.

Put the gear motor MAX on the plate "Pb", take

away the protection cover and fix the Max by

suitable supplied screws "Vf"

Loose the screws "Vt" and make the plate "Pb" run

in the suitable holes "Fr" to establish a distance

between the operator's pinion "P" and the gate

suitable to the type of rack "C" you want to install.

The tooth of the pinion must mesh with the teeth of

the rack for all its width

Carry out an emergency or manual manoeuvre

(see the par. "Emergency or manual manoeuvre")

and put the gate in the maximum opening position.

Lean one end of the rack "C" on the pinion "P",

make sure that it's horizontal and fix it by welding

or by the suitable screws "Vc"

make slide the gate, checking that the rack don't

force on the pinion and that don't go away.

If the gate is crooked put between the gate and the

rack some thickness to assure the constant

centring between the rack and the pinion.

After fixing definitively the rack "C" loose slightly the

screws "Vp" and adjust the play-gap between rack

and pinion (2 mm aprox.) using the plate "Pb" holes

"Fr", to position correctly the operator

When everything has been done fix the screws

"Vp" and with a manual manoeuvre open and close

the gate to verify the correct alignment (there have

not been friction).

instructions

for

1).

2).

(fig.

3).

(fig.

4).

(fig.

5), fixing the rack

(fig.

6).

the

The duration of the rack and the pinion depend on

the right mesh engagement.

The gates must have mechanical stops "Fa"

in opening and closing to avoid its derailment.

The mechanical stops "Fa" must ensure an antic

rushing space between the mobile and fix part of

the gate,

In conformity with the regulations in force.

Put the gate in opening position and, according to

fig.

the gate weight, leave a space of 30-50 mm

between the gate and the mechanical stop "Fa"

7).

Fix on the rack the limit switch support "S" by grubs

"Gr" in order to push the limit switch

Repeat the same operation on the other side, for

the closing limit switch support.

Make the circuitry like in the control panel manual

and install the obligatory safety devices.

Teach the people intended for the use of the

automation about the controls, safety devices,

emergency manoeuvre and dangerousness

deriving from the utilize of the automation.

Compile the technical booklet and fulfil the

eventual obligations deriving from the regulations

in force.

We Guarntee the correct functioning of MAX

versions only and exclusively if provided by

DASPI and only if combined with the original

control panel.

EMERGENCY OR MANUAL MANOEUVRE

You have to do the emergency or manual

manoeuvre or during the installation, or only if the

automation does not work properly or if there is not

power supply.

CUT OFF THE POWER SUPPLY.

Open the plug on the handle "LS" cover and insert

the supplied key "CH"

Turn the key "CH" anticlockwise and take out the

handle of 90° towards you

gate manually.

In order to re-establish the normal functioning of

the automation, you have to put again the handle

"LS" in the original position and turn the key "CH"

clockwise, so take away the key and close the plug

on the handle.

Place the key "CH" in a safety place known

exclusively from the people intended for the use of

the automation.

Switch on the power supply, pay attention that

there's nobody where the gate is moving.

IMPORTANT

(fig.

9).

(fig.

9) and open the

(fig.

8).