Duren 321240 Instrukcja obsługi - Strona 3

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Rozpylacz farby Duren 321240. Duren 321240 13 stron. Electric hvlp turbine spray gun system

Drukuj stronę
PLEASE KEEP THIS MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE

Electrical Safety Instructions

The owner and/or the operator MUST read, understand and comply all points listed below.
1
You MUST check all electrical products, before use, to ensure that they are safe.
2
You MUST inspect plugs, sockets, power leads and any other connectors for wear or damage.
3
You MUST have any worn or damaged plugs, sockets and power leads replaced immediately
upon discovery.
4
You MUST ensure that the risk of electric shock is minimised by the installation of appropriate
safety devices.
5
A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. - If
no RCCB is fitted, use of a Residual Current Device (RCD) is strongly recommended. If you are
unsure, speak to a qualified electrician and have an RCCB fitted if necessary.
6
RCDs are available from most electrical retailers.
7
The Electricity at Work Act 1989 requires that all portable electrical appliances, if used on commercial
premises, should be tested using a Portable Appliance Tester (PAT) at least once a year.
8
The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the
safe condition of those appliances and the safety of the appliance operators. If in any doubt about
electrical safety, seek advice from the governing body or independent electrical training providers.
9
Ensure that the insulation on all cables and on the appliance are safe and intact before connecting it
to the power supply.
10
Ensure that cables are always protected against short circuit and overload.
11
Regularly inspect power supply cables and plugs for wear or damage and check all connections to
ensure that none is loose or damaged.
12
Ensure that the voltage rating of the tool matches your power supply and that the plug is fitted with
the correct fuse.
13
Do not yank the plug from the socket as can cause damage to both plug and socket. Any damage to
plugs or sockets is potentially lethal.
14
Never carry any electrical tool by it's power lead.
15
If you are using an extension reel, ensure that it is fully unwound and that an RCD is fitted. A
minimum cable core of 1.5mm
loads can be handled, if working at over 20m, then a core of 4mm
extension reel needs to be marked for outdoor use if working outside.
16
The Electricity at Work Act 1989 requires that all portable electrical appliances, if used on commercial
premises, should be tested using a Portable Appliance Tester (PAT) at least once a year.
17
When the ASTA/BS approved UK 3 pin plug is damaged, cut the cable close to the plug and dispose
of the it safely. Fit a new plug according to the following instructions;
1: Connect the BROWN live wire to the live terminal 'L'.
2: Connect the BLUE neutral wire to the neutral terminal 'N'.
3: After wiring, check that there are no bare wires, that all wires
have been correctly connected, that the cable outer insulation
extends beyond the cable restraint and that the restraint is tight.
The plug fitted to this tool is fitted with a 13amp fuse.
This product is double insulated and marked with this symbol. It is fitted with
live (brown) and neutral (blue) wires only.

General Safety Instructions

1
Not for use with paint or other materials with a flashpoint of less that 55
2
Users must choose the correct spraygun, with suitable setup and paint flow, for the job requirement.
3
Before connecting the spraygun, check the main voltage is compatible with appliance.
4
Follow all HSE guidelines on electrical tools and their use as well as your own Electrical Health &
Safety Policy. Always use an earthed electrical supply.
5
Switch off motor before refilling, cleaning or servicing the spraygun.
6
Never leave your spraygun exposed to dust, silicone, acids vapors, explosive or flammable gases,
rain, sun, fog or snow.
7
Ensure the cable cannot be twisted, pinched or damaged.
8
NEVER carry tool by the power lead.
is recommended although a core of 2.5mm
2
Duren Tools
T: 01582 484875 E: [email protected]
www.duren.co.uk
will ensure that heavy
2
is strongly recommended. Your
2
C. If in doubt consult MSDS*.
o
*MSDS
Material Safety Data Sheet