4max PP-MESC120AHV Instrukcje programowania - Strona 3
Przeglądaj online lub pobierz pdf Instrukcje programowania dla Akumulator 4max PP-MESC120AHV. 4max PP-MESC120AHV 3 stron.
Drukuj stronęProgramming via the Transmitter
1. Enter program mode
Push the throttle stick to
the top position (full On
throttle), turn on the
transmitter, connect the
ESC, wait 2 seconds, you
will hear two "beeps"
which means the full
throttle is confirmed. Wait
another 6 seconds, it will
make "♪ i 3 i 3" tune, then
you can start
programming via
transmitter
3. Select program values
After entering parameter setting status, you will hear the ESC making sounds in cycle.
Different sounds indicate different values. Push the throttle stick to the top position (full
On throttle) within 3 seconds after you hear the correspondent sound, then you will hear a
special tune "♪ 5 6 5 6", which means the correspondent value has been chosen and
saved. If you don't want to continue setting other values, just pull the throttle stick to the
bottom position (Full Off throttle) to exit. Or wait 3 seconds to return to the second step
and continue programming.
Parameter
"beep-"
1 sound
Brake Type
OFF
Timing Mode
Low
Start Mode
Fast
Cut off Mode
Soft
Throttle
Curve1
Curve
Li-XX Cells
Automatic
Cut off
Low （ （ （ （ 2.60V ） ） ） ）
Voltage
Motor
Normal
rotation
Remarks: Under Li-XX Cells value status, when the number of Li-xx battery cell is more than
4, the ESC will indicate by making long "beep" plus short "beep" sounds, a long "beeeep"
sound equals 5 short "beep" sound. E.g. you will hear "beep-----beep-" (a long sound + a
short sound) if there is a 6-cell Li-xx pack and you will hear "beeeep-----beeeep-----beep-"
(two long sounds + a short sound) for an 11-cell Li-xx pack.
4-Max for quality and affordable brushless motors, ESC's and other electric flight accessories
2. Select program parameters
There're 9 parameters can be set by using your transmitter. You would hear 9 different
indicating sounds which correspond to 9 different parameters. Pull the throttle stick to the
bottom position (full Off throttle) within 3 seconds after you hear the correspondent sound
will brings you to the correspondent parameter setting status. The indicating sounds will
repeat in turn as follow (1 long sound=5short sounds):
1. "beep-" (a short sound) which indicates the Brake Type
2. "beep-beep-" (two short sounds) which indicates the Timing Mode
3. "beep-beep-beep-" (three short sounds) which indicates the Start Mode
4. "beep-beep-beep-beep-" (four short sounds) which indicates the Cutoff Mode
5. "beep-----" (a long sound) which indicates the Throttle Curve Mode
6. "beep-----beep-" (a long sound and a short) which indicates the Li-XX Cells
7. "beep-----beep-beep-" (a long sound and two short) which indicates the Cutoff Voltage
8. "beep-----beep-beep-beep-" (a long sound and three short) which indicates Motor
rotation reversible.
9. "beep-----beep-----beep-----"(three long sound) EXIT
"beep-beep-"
"beep-beep-
2 sounds
beep-"3
sounds
Soft
Hard
Mid
High
Soft
Very soft
Hard
Curve2
Curve3
2 cells
3cells
Middle （ （ （ （ 2.85V ） ） ） ）
High （ （ （ （ 3.10V ） ） ） ）
Reverse
www.4-Max.co.uk
.
"beep-beep---
"x
sounds
xx cells
4. Exit program
Exit programming: Two
ways as shown in step2
and step3.