Datasensor S62-M2 Series Instrukcja obsługi

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Akcesoria Datasensor S62-M2 Series. Datasensor S62-M2 Series 4 stron.

Drukuj stronę

S62...B

Polarised retroreflex

INSTRUCTION MANUAL

CONTROLS

OUTPUT LED (yellow)

The yellow LED ON indicates the following output

status: N.O. closed and N.C. open.

STABILITY LED (green)

The green LED permantely ON indicates a stable

operating condition, where the signal received has a

safety margin higher than 30% respect to the output

switching value. The sensor is ready to function

correctly.

SENSITIVITY TRIMMER (ADJ.)

A mono-turn trimmer adjusts the sensitivity and the

sensor operating distance.

See the "SETTING" paragraph for the functioning

mode.

NOTE: the maximum trimmer mechanical rotating

range is equal to 240°. Do not force over the maximum

e minimum positions.

INSTALLATION

The

sensor

can

positioned by means of

the

three

housing's

holes using two screws

(M4x25 or longer, 1.5

Nm maximum tightening

torque) with washers.

Various orientable fixing

brackets to ease the sensor positioning are available

(please refer to the accessories listed in the

catalogue).

The operating distance is measured from the front

surface of the sensor optics.

The M12 connector can be oriented at two different

positions using the specific fastening spring and

rotating the block of 180°.

TECHNICAL DATA

Power supply:

Ripple:

Current consumption

(output current excluded):

Outputs:

Output current:

Output saturation voltage:

Response time:

Switching frequency:

Indicators:

Setting:

Operating temperature:

Storage temperature:

Dielectric strength:

Insulation resistance:

Operating distance (typical values):

Emission type:

Ambient light rejection:

Vibrations:

0.5 mm amplitude, 10 ... 55 Hz frequency, for each axis (EN60068-2-6)

Shock resistance:

Housing material:

Lens material:

Mechanical protection:

Connections:

Weight:

CONNECTIONS

Alignement:

- Align sensor and reflector on opposite sides at the necessary

distance.

- Rotate in the clockwise direction the sensitivity adjustment

trimmer (ADJ.) to maximum level.

- Moving the sensor vertically and horizontally, establish the

powering and turning off of the yellow LED (OUT) and fix the

sensor at in the middle. The best alignment is obtained in the

following condition: yellow LED permanently OFF and green

LED permanently ON.

Control:

- Place the target between the

sensor and the reflector. Control

that the yellow LED turns ON.

- Remove the target and control

that the yellow LED turns OFF again.

10 ... 30 Vdc (limit values)

2 Vpp max.

< 30 mA

PNP or NPN N.O. / N.C.; 30 Vdc max. (short-circuit protection)

100 mA max (overload and overvoltage protection)

≤ 2 V

500 µs max.

1 kHz

OUTPUT LED (YELLOW) / STABILITY LED (GREEN)

mono-turn sensitivity adjustment trimmer

-10 ... 55 °C

-20 ... 70 °C

500 Vac / 1 min. between electronic parts and housing

>20 MΩ / 500 Vdc, between electronic parts and housing

0.1...8 m su R2 (EG = 2)

RED (640 nm)

according to EN 60947-5-2

11 ms (30 G) 6 shocks for each axis (EN60068-2-27)

ABS

window in PMMA, lenses in polycarbonate

IP67

2 m ∅ 4 mm cable / M12 4-pole connector

90 g. max. (cable version) / 40 g. max. (connector version)

SETTING

DIMENSIONS

4.7

11 6

M12

Ø15

SENSITIVITY TRIMMER

CABLE VERSION

6.18

10.7

STABILITY LED

OUTPUT LED

EX-II-3D T6

T6 (<85°C)

Temperature class:

Max. Power consumpti 540 mW at 30 Vdc

Max. Internal capacitan 100 nF

Internal inductance:

negligible

DECLARATION OF CONFORMITY

We DATASENSOR S.p.A. declare under our sole responsibility that

these products are conform to the 2004/108 CEE, 73/23 CEE Directives

and successive amendments.

WARRANTY

DATASENSOR S.p.A. warrants its products to be free from defects.

DATASENSOR S.p.A. will repair or replace, free of charge, any product

found to be defective during the warranty period of 36 months from the

manufacturing date.

This warranty does not cover damage or liability deriving from the

improper application of DATASENSOR products.

DATASENSOR S.p.A. Via Lavino 265

40050 Monte S. Pietro - Bologna - Italy

Tel: +39 051 6765611

Fax: +39 051 6759324

http://www.datasensor.com

e-mail: [email protected]

DATASENSOR S.p.A. cares for the environment: 100% recycled

paper.

DATASENSOR S.p.A. reserves the right to make modifications

and improvements without prior notification.

826003020 Rev.00