GAC ESD5550M Podręcznik
Przeglądaj online lub pobierz pdf Podręcznik dla Jednostka sterująca GAC ESD5550M. GAC ESD5550M 8 stron. Speed control unit
Drukuj stronę
1
INTRODUCTION
The ESD5550/5570 series speed control unit is an all electronic device designed to
control engine speed with fast and precise response to transient load changes. This
closed loop control, when connected to a proportional electric actuator and supplied
with a magnetic speed sensor signal, can control a wide variety of engines in an iso-
chronous or droop mode. Designed for high reliability and built ruggedly to withstand
the engine environment. ESD5550/5570 Series speed control unit features include:
•
Simple installation
•
Starting Fuel and Speed Ramping adjustments to minimize engine exhaust
smoke prior to attaining engine operating speed
•
Adjustable droop and idle operation
•
Inputs for accessories used in multi-engine or special applications
•
Protection against reverse battery voltage, transient voltages, accidental short
circuit of the actuator and fail safe design in the event of loss of speed sensor
signal or battery supply.
•
Light Force Actuation (ESD5570 only)
The ESD5550/5570 Series speed control unit is compatible with all GAC proportional
actuators (except ACB2001). When paired with a GAC ADC100 Series electric ac-
tuator, DROOP adjustment range is less due to the ADC100's low current demand.
2
SPECIFICATIONS
Performance
Isochronous / Steady State
Stability
Speed Range / Governor
Speed Drift with Temperature
Idle Adjust CW
Idle Adjust CCW
Droop Range
Droop Adjustment MAX
(K-L Jumpered)
Droop Adjustment MIN
(K-L Jumpered)
Remote Variable Speed Range
Speed Trim Range
Terminal Sensitivity
InPUT / oUTPUT
Operating Voltage
Polarity
Power Consumption
Actuator Current Range at 77 °F
(25 °C) - Inductive Load
Speed Sensor Signal
Speed Switch Relay Contacts
(N.O. and N.C.)
ESD5550 & ESD5570 Series
Speed Control Unit
± 0.25 % or better
1 K - 7.5 K Hz continuous
60 % of set speed
Less than 1200 Hz
1 - 5 % regulation
400 Hz, ±75 Hz per 1 A change
415 Hz, ±75 Hz per 1 A change
500 - 7.5 Hz or any part thereof
J
100 Hz ±15 Hz/V @ 5.0 kΩ Impedance
L
735 Hz ±60 Hz/V @ 65 kΩ Impedance
N
148 Hz ±10 Hz/V @1 MΩ Impedance
P
10 V DC Supply @ 20 mA MAX
12 VDC or 24 VDC (Transient and
Reverse Voltage Protected)*
Negative Ground (Case Isolated)
50 mA continuous plus actuator current
Minimum 2.5 A
0.5 to 120 V RMS
Vibration
Testing
±1 % MAX
Ambient Temperature Range
Relative Humidity
Shock
All Surface Finishes
Agency
Dimension
± 200 Hz
Weight
Mounting
10 A Peak**
* Protected against reverse voltage by a series diode. A 15 amp fuse must be installed in
the positive battery lead.
** Protected against short circuit to actuator (shuts off current to actuator), unit automati-
10 A
cally turns back on when short is removed.
1
ESD5550-5570 Series Speed Control Unit 1-2021-E1 PIB1003
Governors America Corp. © 2021 Copyright All Rights Reserved
reLIaBILITY
100% Functional Testing
envIronmenTaL
-40° to 85 °C [-40° to 180 °F]
Fungus Proof, Corrosion Resistant
comPLIance / STanDarDS
CE, RoHS, Lloyds Register,
DNV/GL, Bureau Vertas
PHYSIcaL
See Section 3, Installation
Any position, vertical preferred
5 g @ 20 - 500 Hz
up to 95 %
20 g @ 11 ms
1.8 lbf [0.82 kgf]