Hi-Force HVL Series Instrukcja obsługi
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Urządzenia przemysłowe Hi-Force HVL Series. Hi-Force HVL Series 4 stron. Single-acting, very low height pancake cylinders
Również dla Hi-Force HVL Series: Instrukcja obsługi (13 strony)
Drukuj stronę
Model Series: HVL, HPS, HLS, HSS, HAS, HHA, HHS, HHR, HDA, HFL, HFG, HSG, HGG, HPC.
NOTE: Spare parts sheets for these products are
available from the Hi-Force website at:
www.hi-force.com
or from your local regional Hi-Force Sales office or
authorized local Hi-Force distributor.
1.0 Inspection of the product upon receipt:
On receipt of the product, visually inspect the item
for any evidence of shipping damage. Please note
shipping damage is not covered by warranty. If
shipping damage is found notify the carrier
immediately and refrain from putting the product
into service. The carrier is responsible for repair
and replacement costs resulting from damage in
transit shipment.
2.0 Safety Precautions:
Read and follow all the instructions and safety
warnings carefully prior to use of the equipment.
Failure to do so could result in equipment damage
or failure of the equipment or personal injury. Hi-
Force will not be held responsible for any damage
to the equipment or personal injury resulting from
unsafe use of the product, lack of maintenance or
incorrect operation. If in doubt on the correct usage
of any Hi-Force equipment, contact your nearest Hi-
Force office or distributor. If the operator has not
been trained on high pressure hydraulic equipment
and its safe use consult your local Hi-Force sales
office who can offer you training courses for
operators.
All operators should ensure that all necessary
personal protective equipment as specified by their
employer is worn when operating any hydraulic
equipment. Safety shoes, safety glasses/ visor and
Hi-Force Limited – Prospect Way – Daventry – Northants NN11 8PL – United Kingdom
Tel: +44(0) 1327 301000: Fax: +44(0) 1327 706555: Website: www.hi-force.com
INSTRUCTION MANUAL – HYDRAULIC CYLINDERS:
protective gloves should be worn at all times. All
relevant risk assessments should be completed
prior to use of the equipment.
Warning: Do not work under a load supported
only by hydraulic means. A cylinder, when used as a
lifting device should not be used as a load holding
device. All loads once lifted, should be supported by
rigid mechanical means. If load holding is required
by the application where external mechanical
means cannot be used, HFG/HFL Failsafe cylinders
should be considered. To avoid personal injury keep
hands and feet clear of the cylinder and workpiece
during operation.
Do not exceed the rated capacity of the
hydraulic cylinder and never attempt to lift a load
greater than the stated capacity of the cylinder. Hi-
Force hydraulic cylinders are designed for a
maximum working pressure of 700 BAR (10,000
PSI). Do not connect a pump with a higher rated
pressure capacity to any Hi-Force cylinder of this
model series.
Keep hydraulic equipment away from flames
and direct heat.
Hydraulic equipment must only be serviced by a
qualified technician.
To protect your warranty, only use Hi-Force's
hydraulic oil.
Immediately replace any worn or damaged parts
using genuine Hi-Force parts only.
Do not adjust the external pressure relief valve on
any Hi-Force cylinder.
The system operating pressure must not exceed the
pressure rating of the lowest component in the
system. Where possible, use a pressure gauge to
monitor the system.
Avoid damaging hydraulic hose. Always route hoses
to ensure that they are free from sharp bends and
kinks. Using a bent or kinked hose will cause severe
back-pressure and can also lead to the failure of the
hose.
Never lift or carry any hydraulic components
by the hose or hoses connected to them.
Do not handle a pressurized hydraulic hose.
Oil escaping under pressure from a ruptured
hose can penetrate the skin and lead to a serious
medical emergency and in certain cases death.
Should this incident happen medical attention must
be sought immediately.