Dynabrade 50348 Instrukcja obsługi - Strona 4

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Sander Dynabrade 50348. Dynabrade 50348 4 stron. 2 hp right angle disc sander

Drukuj stronę

4. Install the 01089 Safety Throttle Lever holding it in place with the 01017 Pin.

Valve Assembly Complete.

RIGHT ANGLE AND MOTOR ASSEMBLY

1. Select .003" (.08mm) thickness in shims from the 52141 Shim Pack. Install

the shims into the 52136 Bearing Plate and then install the 52130 Bearing.

2. Install the bearing/plate assembly onto the 07108 Rotor and hold this

assembly in place with the 50509 Key, pinion gear and the 95998 Retaining Ring.

3. Use a .001" (.03mm) feeler gauge to check the clearance between the

bearing plate and the face of the rotor.

4. The clearance should be .001"(.03mm) to .0015"(.04mm). If the clearance

needs adjustment, repeat steps 1-4 adding or removing shims as required.

5. Lubricate the 07109 Blades (5) with the 95842 Dynabrade Air Lube

(10W/NR or equivalent) and install these into the vane slots in the rotor.

6. Install the 52139 Cylinder over the 07108 Rotor so that the air inlet opening

of the cylinder will line up with the air inlet opening in the 52140 Bearing Plate.

7. Use the 96232 Arbor press to install the 01266 Bearing into the 52140 Bearing Plate.

8. Use the raised inner diameter of the 96244 Bearing Press Tool so that it

MOUNTING ARRANGEMENT

LIMITED LIFETIME WARRANTY

Dynabrade portable pneumatic power tools are rigorously inspected and performance tested in our factory before shipping to our customers.

If a Dynabrade tool develops a performance problem and an inherent defect is found during normal use and service, Dynabrade will warrant this

tool against defects in workmanship and materials for the limited lifetime of the tool.

MACHINE SPECIFICATIONS

Model

Power

Sound Level

50348 2 hp (1,491 W)

82 dB(A)

Additional Specifications: Air Inlet Thread 1/2" NPT • Hose I.D. 1/2" (15 mm)

OPTIONAL ACCESSORIES

Grease and Grease Gun

• Multi-purpose grease for all

types of bearing, cams, gears.

• High film strength; excellent

resistance to water, steam, etc.

• Workable range 0°F to 300°F.

95541: Push-type grease gun.

95544: 2.5oz. (74ml) tube.

Bearing Separator

96346

Bearing Removal Tool

96214

Bearing Press Tool

96240

REFERENCE CONTACT INFORMATION

American National Standards Institute (ANSI)

www.ansi.org

Compressed Air & Gas Institute (CAGI)

www.cagi.org

DYNABRADE, INC.

8989 Sheridan Drive • Clarence, NY 14031-1419 • Phone: (716) 631-0100 • Fax: 716-631-2073 • International Fax: 716-631-2524

Air Consumption

12.6 CFM/109 SCFM (3,086 LPM)

Dynaswivel

• Swivels 360° at two

locations which allows

an air hose to drop straight

to the floor, no matter how

the tool is held.

95462: 1/2" NPT

Dynabrade Air Lube

• Formulated for pneumatic

• Absorbs up to 10% of

• Prevents rust and formation of sludge.

• Keeps pneumatic tools operating longer

European Committee for Standardization

(PNEUROP)

www.pneurop.org

International Organization of Standards (ISO)

www.iso.org

will rest against the inner race of the 01266 Bearing. Carefully press the

bearing/plate assembly onto the 07108 Rotor until it touches the 52139 Cylinder.

This will establish a snug fit between the bearing plates and the cylinder.

9. Hold the pinion in a vise with aluminum or bronze jaws so that the female

threaded end of the rotor is pointing up.

10. Apply a small amount of the Loctite #567 (or equivalent) to the threaded stem of

the 52171 Governor Cage and install the governor assembly onto the 07108

Rotor turning it counterclockwise. (Left Hand Thread) (Torque to 9 N•m/80 in. lbs.)

11. Install the motor assembly into the 52146 Housing.

12. Hold the 52146 Housing in a vise with aluminum or bronze jaws by holding the

housing between the handle mounting boss and the 52164 Exhaust Cover.

13. Apply a small amount of the Loctite #567 (or equivalent) to the threads of the

52123 Adapter and install the adapter along with the valve body assembly.

(Torque to 40 N•m/350 in. lbs.)

Important: Remove the tool from the vise and connect it to the air supply.

Test run the tool to make sure that the air motor is functioning properly.

Spindle Thread

Air Pressure

5/8"-11 Male

90 PSIG (6.2 Bar) 8.6 lb. (3.9 kg) 15.8" (399 mm) 5.3" (132 mm)

equipment.

its weightin water.

with greater power and less down time.

95842: 1pt. (473 ml)

95843: 1 gal. (3.8 L)

www.dynabrade.com

Weight

Length

Motor Tune-Up Kit

• Includes assorted parts

to help maintain and

repair motor.

96043

Hex Key

95266: 3mm Hex Key

95051: 3/8" Hex Key

Wrench

95304: 24mm Open-End

96079: 32mm Open-End

U.S. Government Publishing Office (GPO)

www.gpo.gov

Height