Dynabrade Dynorbital-Spirit 21064 Instrukcja obsługi i konserwacji

Przeglądaj online lub pobierz pdf Instrukcja obsługi i konserwacji dla Sander Dynabrade Dynorbital-Spirit 21064. Dynabrade Dynorbital-Spirit 21064 13 stron. 12,000 rpm air powered random orbital sander
Również dla Dynabrade Dynorbital-Spirit 21064: Instrukcja obsługi i konserwacji (8 strony), Podręcznik (13 strony)

Drukuj stronę

For Serial No. 7B1000E and Higher

Dynorbital-Spirit

Models:

3/8" Orbit

3/16" Orbit

21000 21011

21020 21031

21001 21014

21021 21034

21004 21015

21024 21035

21005 21016

21025 21036

21006 21019

21026 21039

21009 21060

21029 21061

21010 21063

21030 21064

FOR COMPLETE MODEL DESCRIPTION REFERENCE PAGE 6.

FIND THE MOST CURRENT OFFERING OF SUPPORT DOCUMENTS AND ACCESSORIES @ WWW.DYNABRADE.COM

Read and understand this tool manual before operating your air tool. Follow all safety rules for the protection of operating personnel

as well as adjacent areas. Always operate, inspect and maintain this tool in accordance with the American National Standards

Institute (ANSI) Safety Code for Portable Air Tools – B186.1. For additional safety information, refer to Safety Requirements for the

Use, Care and Protection of Abrasive Wheels – ANSI B7.1, Code of Federal Regulation – CFR 29 Part 1910, European Committee for

Standards (EN) Hand Held Non-Electric Power Tools – Safety Requirements and applicable State and Local Regulations.

Read and understand tool manual before

work starts to reduce risk of injury to

operator, visitors, and tool.

Eye protection must be worn at all times,

eye protection to conform to ANSI Z87.1.

Respiratory protection to be used when exposed to

contaminants that exceed the applicable threshold

limit values required by law.

Some dust created by sanding, grinding, drilling, and other construction activities contain chemicals known to cause cancer, birth

defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints

• Crystalline silica from bricks and cement and other masonry products

• Arsenic and chromium from chemically treated lumber

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well

ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

Carefully Read all instructions before operating or servicing any Dynabrade

Products offered by Dynabrade are not to be modified, converted or otherwise alerted from the original design without expressed written consent from Dynabrade, Inc.

Tool Intent: Dynorbital-Spirit

Random Orbital Sander is used for sanding and finishing a variety of materials including wood, metal, plastic, fiberglass, solid surfaces,

composites, rubber, glass and stone.

This power tool is not intended for use in potentially explosive atmospheres and is not insulated against contact with electrical power.

Training: Proper care, maintenance, and storage of your tool will maximize its performance.

• Employer's Responsibility – Provide Dynorbital-Spirit

Accessory Selection:

• Abrasive/accessory RPM (speed) rating MUST be approved for AT LEAST the tool RPM rating.

• Before mounting an accessory, visually inspect for defects. Do not use defective accessories.

• Follow tool specifications before choosing size and type of accessory.

• Only use recommended fittings and air line sizes. Air supply hoses and air hose assemblies must have a minimum working pressure rating of 150 PSIG (10 bars, g) or 150

percent of the maximum pressure produced in the system, whichever is higher. (See Tool Machine Specifications Table.)

Air Tool Manual – Safety, Operation and Maintenance

SAVE THIS DOCUMENT, EDUCATE ALL PERSONNEL

3/32" Orbit

21040 21051

21041 21054

21044 21055

21045 21056

21046 21059

21049 21062

21050 21065

WARNING

SAFETY LEGEND

WARNING

SAFETY INSTRUCTIONS

Do Not Use Tool For Anything Other Than Its Intended Applications.

operators with safety instructions and training for safe use of tools and accessories.

12,000 RPM Air Powered Random Orbital Sander

Practice safety requirements. Work alert,

have proper attire, and do not operate tools under

the influence of alcohol or drugs.

Ear protection to be worn when exposure to sound,

exceeds the limits of applicable Federal, State or

local statues, ordinances and/or regulations.

Air line hazard, pressurized supply lines and flexible

hoses can cause serious injury. Do not use damaged,

frayed or deteriorated air hoses and fittings.

WARNING

Abrasive Power Tool.

AUTOMOTIVE

Parts Page Reorder No. APD07•03

Effective February, 2007

Supersedes APD03•02

WARNING