Dynabrade 52213 Instrukcja obsługi - Strona 2

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Szlifierka Dynabrade 52213. Dynabrade 52213 4 stron. .5hp/7˚/front exhaust/short shank die grinder
Również dla Dynabrade 52213: Podręcznik (4 strony), Podręcznik (4 strony)

Drukuj stronę

Disassembly/Assembly Instructions-.5 Hp/7°/Front Exhaust

Important: Manufactures warranty is void if tool is disassembled before warranty expires.

Please refer to parts breakdown for part identification.

To Disassemble:

1. Secure air tool in vise using or padded jaws.

2. Remove collet cap and insert.

3. With an adjustable pin wrench, remove 04087 Lock Ring by turning counter-clockwise. Remove air control silencer and fabric silencer.

4. Pull motor assembly from housing.

5. Reposition motor housing in vise so inlet bushing is facing upwards.

6. Unscrew 01494 Inlet Bushing turning counter-clockwise.

7. Using needle nose pliers, remove 01468 Spring, 01472 Tip Valve and 01464 Seal.

8. Resecure housing in vise so throttle lever and 12132 Pin are accessible.

9. Using a 2.5 mm diameter drift pin and a hammer, tap 12132 Pin out from housing and remove throttle lever.

10. Remove 95558 Retaining Ring and push 01469 Speed Regulator from Housing.

Optional: To disassemble valve body from motor housing, peel back 01558 Collar to expose 01462 Lock Nut. Unscrew lock nut/valve body from housing

(left hand threads).

Motor Disassembly:

1. Remove 50062 Collet Body from rotor shaft by inserting 3/16" hex wrench through collet body and into rotor shaft. Twist collet body from shaft.

2. Remove 01008 Front Bearing Plate, cylinder, blades (4) and 01149 Spacer from rotor.

Note: 01007 Bearing, 01008 Front Bearing Plate and 01149 Spacer are a slip fit onto rotor.

3. Press rotor from 01014 Rear Bearing Plate. Press 01015 Bearing from bearing plate.

Motor disassembly is complete.

Motor Reassembly

Important: Be sure parts are clean and in good repair before reassembly

1. Place rotor in padded vise with a threaded spindle facing upwards.

2. Slip 01149 Spacer onto rotor.

3. Place a .002" shim into 01008 Front Bearing Plate as an initial spacing (Note: 01121 Shim Pak contains .001" and .002" shims) and slip 01007

Bearing into plate.

4. Install Bearing/Bearing Plate assembly onto rotor.

5. Tighten 50062 Collet Body onto rotor (torque to 150 in. - lbs.).

6. Check clearance between rotor and bearing plate by using a .001" feeler gauge. Clearance should be at .001" to .0015". Adjust clearance by repeating

steps 1-5 with different shim if necessary.

7. Once proper rotor/gap clearance is achieved, install well lubricated 01011 Blades (4) into rotor slots. Dynabrade air lube P/N 95842 is recommended

for lubrication.

8. Install cylinder over rotor. Be sure air inlet holes of cylinder face away from bearing plate.

9. Press 01015 Rear Bearing into 01014 Rear Bearing Plate. Press bearing/bearing plate assembly onto rotor. Be sure that pin and air inlet holes line-up with pin slot

and air inlet holes in cylinder.

Important: Fit must be snug between bearing plates and cylinder. If too tight, rotor will not turn freely. Rotor must then be lightly tapped at press fit end so it

will turn freely while still maintaining a snug fit. A loose fit will not achieve the proper preload of motor bearings.

10. Secure motor housing in padded vise so motor cavity faces upwards.

11. Install motor assembly into housing. Be sure motor drops all the way into housing.

12. Insert air control silencer and fabric silencer into 04087 Lock Ring and install onto motor housing (torque 150 in. - lbs.).

13. Motor adjustment must now be checked. With motor housing still mounted in vise, pull end of rotor and twist (10-15 lbs. force), rotor should turn freely

without drag. If drag or rub is felt, then increase preload or remove shim. Also, push end of rotor and twist (10-15 lbs. force), rotor should turn freely

without drag. If drag or rub is felt, then deload or add shim.

Valve Stem/Body Reassembly:

1. Insert 01469 Speed Regulator Assembly into valve body. Secure with 95558 Retaining Ring.

2. Secure valve body in vise using padded jaws with air inlet facing upwards and throttle lever accessible.

3. Insert 01464 Seal into housing.

4. Line-up the hole in the 01449 Valve Stem with the hole in the housing (looking past brass bushing). Using needle nose pliers, insert 01472 Tip Valve so

that the metal pin passes through the hole in the valve stem.

5. Install 01468 Spring (small end towards the tip valve).

6. Apply 1 drop of #271 Loctite (or equivalent) to threads of 01494 Inlet Bushing and install into valve body (torque 34.0 N•m 200 lbs. in.).

7. Install throttle lever and 12132 Pin. Remove valve body from vise.

Tool Assembly is complete. Please allow 30 minutes for adhesives to cure before operating tool.

Important: Motor should now be tested for proper operation at 90 PSI. If motor does not operate properly or operates at a higher RPM than marked on the

tool, the tool should be serviced to correct the cause before use.

Note: Throttle lever is preset at the factory at an 11:00 o'clock position.

Loctite® is a registered trademark of Loctite Corp.