Dynabrade 52333 Instrukcja obsługi - Strona 4

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Szlifierka Dynabrade 52333. Dynabrade 52333 4 stron. 4 hp/7/rear exhaust

Drukuj stronę
Dynabrade 52333 Instrukcja obsługi
Disassembly/Assembly Instructions (continued)
8. Install 95711 Retaining Ring into groove at the male threaded end of the inlet adapter. Install 96065 O-Ring into groove on the air defector.
9. Apply Loctite
#567 (or equivalent) to the male threads of the 01578 Inlet Adapter and install muffler assembly onto valve body housing (torque
®
to 23 N•m/200 in.-lbs.).
10. Install 01448 or 01462 Throttle Lever onto valve body housing with 12132 pin.
11. Secure 01578 Inlet Adapter with a wrench to prevent it from turning. While holding the inlet adapter stationary install the air fitting by turning it clockwise.
Important: 01578 Inlet Adapter must be secured before attempting to install the air fitting so as to avoid damaging the valve body housing.
Notice: To adjust throttle body orientation for a rear exhaust tool:
1. Use 52296 Repair Collar to secure valve body in vise with 01546 Housing facing up.
2. Peel down 01558 Collar to expose the nut portion of 01461 Lock Nut.
3. Using a 34 mm crows foot and firmly holding motor housing, turn 01461 Lock Nut counterclockwise to loosen assembly.
4. Adjust orientation of the throttle lever to agree with your grip and comfort level allowing for additional rotation due to torquing.
5. Using the 34 mm crows foot torque 01461 Lock Nut to 45 N•m/400 in.-lbs. while firmly holding motor housing in place to reduce housing rotation.
Tool Assembly Complete. Please allow 30 minutes for adhesives to cure before operating tool.
Important: Motor should now be tested for proper operation at 90 PSIG. If motor does not operate properly or operates at a higher RPM than marked on the
tool, the tool should be serviced to correct the cause before use.
Loctite
®
is a registered trademark of Loctite Corp.
96049 Motor Tune-Up Kit
•
Includes assorted parts to help maintain
and repair motor.
50971 Lock Ring Tool
•
Lock Ring Tool has a 3/8 in. square socket
for use with 3/8 in. drive; breaker bar,
ratchet head, or torque wrenches.
Visit our Web Site: www.dynabrade.com
DYNABRADE, INC., 8989 Sheridan Drive • Clarence, NY 14031-1490 • Phone: (716) 631-0100 • Fax: 716-631-2073 • International Fax: 716-631-2524
DYNABRADE EUROPE S.àr.l.,
© DYNABRADE, INC., 2001
Optional Accessories
Collet Inserts
•
01485 1/4"
•
01497 6 mm
•
01495 1/8"
•
01496 3 mm
Zone Artisanale • L-5485 Wormeldange—Haut, Luxembourg • Telephone: 352 76 84 94 1 • Fax: 352 76 84 95 1
52296 Repair Collar
•
Specially designed collar for use in vise to
prevent damage to valve body housing during
disassembly/assembly.
Dynaswivel
Swivels 360° at two locations which allows an
air hose to drop straight to the floor, no matter
how the tool is held.
•
94300 1/4" NPT.
Open-End Wrenches
96076 – 12 mm open-end.
95262 – 14 mm open-end.
®
®
DYNABRADE
PRINTED IN USA