Dynabrade 52716 Bezpieczeństwo, obsługa i konserwacja - Strona 3
Przeglądaj online lub pobierz pdf Bezpieczeństwo, obsługa i konserwacja dla Szlifierka Dynabrade 52716. Dynabrade 52716 8 stron. 1hp cone or plug grinder governor controlled
Drukuj stronę
Important:
A Preventative Maintenance Program is recommended whenever portable grinders are used.
Use only genuine Dynabrade replacement parts to insure quality. To order replacement parts, specify
•
All Dynabrade Rotary Vane air tools must be used with a Filter-Regulator-Lubricator to maintain all warranties. Dynabrade recommends the following:
•
11411
Air Filter-Regulator-Lubricator (FRL) – Provides accurate air pressure regulation and two stage filtration of water contaminants. Operates 55
SCFM/1,558 LPM @ 90 PSIG with 1/2" NPT female ports.
Dynabrade recommends one drop of air lube per minute for each 10 SCFM (example: if the tool specification states 40 SCFM, set the drip rate on the
•
filter-lubricator to 4 drops per minute). Dynabrade Air Lube (P/N
Routine Preventative Maintenance:
checked every 20 hours of use or weekly, whichever occurs more frequently.
DO NOT disassemble the governor for any reason. Reorder correct speed – governor assembly (See Assembly Breakdown) and recheck free speed of
•
tool with a tachometer.
Periodically remove the accessory and clean the adapter for debris to keep accessories secure and reduce vibration.
•
Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters,
•
ketones, chlorinated hydrocarbons or nitro carbons.
DO NOT clean or maintain tools with chemicals that have a low flash point (example: WD-40
•
A Motor Tune-Up Kit (P/N
•
Air tool labels must be kept legible at all times, if not, reorder label(s) and replace. (See Assembly Breakdown)
•
Blow air supply hose out prior to initial use.
•
DO NOT carry tool by air hose or near the tool throttle lever.
•
Visually inspect air hoses and fittings for frays, visible damage and signs of deterioration. Replace damaged or worn components.
•
Refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No.
•
After maintenance is performed on tool, add a few drops of Dynabrade Air Lube (P/N
Check for excessive tool vibration.
Handling and Storage:
Use of tool rests, hangers and/or balancers is recommended.
•
Protect tool inlet from debris. (See Notice Below)
•
DO NOT carry tool by air hose or near the tool throttle lever.
•
Protect cone and plugs from exposure to water, solvents, high humidity, freezing temperatures and extreme temperature changes.
•
DO NOT USE cone or plugs that have been dropped or show signs of cracks, nicks or other defects.
•
Store accessories in protective racks or compartments to prevent damage.
•
Model
Motor
Number
HP (W)
52715
1 (744)
52716
1 (744)
52717
1 (744)
52718
1 (744)
Additional Specifications: Air Inlet Thread 3/8" NPT • Hose Size 3/8" (10 mm) • Air Flow Rate Based At Max HP. • Air Pressure 90 PSIG Max
All Dynabrade motors use the highest quality parts and metals available and are machined to exacting tolerances. The failure of quality pneumatic motors
can most often be traced to an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water contained in the air supply into motor
bearings causing early failure. It often scores the cylinder walls and the rotor blades resulting in limited efficiency and power. Our warranty obligation is
contingent upon proper use of our tools and cannot apply to equipment which has been subjected to misuse such as unclean air, wet air or a lack of
lubrication during the use of this tool.
Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from the
date of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. We shall
repair or replace at our factory, any equipment or part thereof which shall, within one year after delivery to the original purchaser, indicate upon our
examination to have been defective. Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations,
instructions and safety practices. It shall not apply to equipment which has been subject to misuse, negligence, accident or tampering in any way so as to
affect its normal performance. Normally wearable parts such as bearings, contact wheels, rotor blades, etc., are not covered under this warranty.
Maintenance Instructions
Check free speed of cone or plug grinder using a tachometer. This governor controlled grinder should be speed
96532
) is available which includes high wear and medium wear motor parts.
Machine Specifications
Motor
Sound
Maximum Air Flow
RPM
Level
CFM/SCFM (LPM)
12,000
82 dB(A)
15,000
83 dB(A)
18,000
84 dB(A)
20,000
88 dB(A)
95842
: 1 pt 473 ml) is recommended.
95903
) for safety information.
95842
) to the air line and start the tool a few times to lubricate air motor.
Spindle
Thread
5/38 (1,076)
3/8"-24 male
5/39 (1,104)
3/8"-24 male
6/40 (1,133)
3/8"-24 male
6/40 (1,133)
3/8"-24 male
(PD01•83)
3
Model#
Serial#
,
and
).
®
Air Pressure
Weight
PSIG (Bars)
Pound (kg)
90 (6.2)
1.9 (.9)
90 (6.2)
1.9 (.9)
90 (6.2)
1.9 (.9)
90 (6.2)
1.9 (.9)
RPM
of your air tool.
Length
Height
Inch (mm)
Inch (mm)
7-3/4 (198)
1-7/8 (48)
7-3/4 (198)
1-7/8 (48)
7-3/4 (198)
1-7/8 (48)
7-3/4 (198)
1-7/8 (48)