2gig Technologies 2GIG-DBELL1-345 Instrukcje instalacji - Strona 2
Przeglądaj online lub pobierz pdf Instrukcje instalacji dla Akcesoria 2gig Technologies 2GIG-DBELL1-345. 2gig Technologies 2GIG-DBELL1-345 2 stron.
Drukuj stronę
Inserting and Replacing Batteries
If a supervised sensor battery is low, a low battery notification will be indicated on the control panel screen. When the 2GIG
system indicates that the sensor has a low battery, replace the battery immediately. Use only the recommended
replacement batteries (See Specifications).
1
To remove the sensor cover, use your finger to press the tab. This disengages the clip holding the cover to the base.
2
Place a small flathead screwdriver in the slot between the metal clip and battery and push it out taking care not to
scratch the battery terminal.
3
Insert the replacement battery with the + sign facing out.
4
Verify programming and RF communication with the control panel.
5
Replace the sensor cover to the base.
WARNING:
The polarity of the battery must be observed, as shown. Improper handling of lithium batteries may
result in heat generation, explosion or fire, resulting in personal injuries. Replace only with the same or
equivalent type of battery as recommended by the manufacturer (see Specifications). Batteries must not be
recharged, disassembled or disposed of in fire. Disposal of used batteries must be made in accordance with the
waste recovery and recycling regulations in your area. Keep Away From Small Children. If batteries are swallowed,
promptly seek medical attention.
California Only: This Perchlorate warning applies only to Manganese Dioxide Lithium cells sold or distributed
ONLY in /California, U.S.A. Perchlorate Material‐special handling may apply. See dtsc.ca.gov/hazardouswaste/
perchlorate.
Specifications
Wireless Signal Range
Code Outputs
Transmitter Frequency
Transmitter Frequency Tolerance
Transmitter Bandwidth
Modulation Type
Unique ID Codes
Supervisory Interval
External Input Sampling Current
External Input
Sensor Dimensions (HxD)
Weight (including battery and magnet)
Housing Material
Color
Operating Temperature Limits
Relative Humidity
Battery (installed with pull tab)
Included Accessories
FCC and Industry Canada Regulatory information
Notice: Unauthorized changes or modifications could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules and Industry Canada license‐exempt RSS standard(s). Operating is subject
to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B computing device, pursuant to Part 15 of
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and the receiver
•
Consult the dealer or an experienced radio/television technician for help
This 2GIG Technologies product is warranted against defects in material and workmanship for 2 years. This warranty extends only to
wholesale customers who buy direct from 2GIG Technologies or through 2GIG Technologies' normal distribution channels. 2GIG
Technologies does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the
dealer's warranty, if any.
There are no obligations or liabilities on the part of 2GIG Technologies for consequential damages arising out of or in connection
with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of
removal, installation, or reinstallation. All implied warranties for functionality, are valid only until the warranty expires. This 2GIG
Technologies Warranty is in lieu of all other warranties express or implied.
All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact 2GIG Technologies at
1(866)670‐1591 for an RPA# and other important details.
Warranty service return address:
350 ft, open air, with 2GIG Wireless Control Panel
Alarm; Alarm Restore; Supervisory; Low Battery
345.000 MHz (crystal controlled)
±15kHz
24kHz
Amplitude Shift Keying‐On/Off Keying (ASK‐OOK)
Over one million different code combinations
70 minutes
20 uA
24V AC Standard doorbell circuit
2.75 x 1.17 x 0.63 in. (6.98 x 2.97x 1.60 cm)
1.1 oz. (31.2 g)
ABS plastic
White
14° to 104° F (‐10° to 40° C)
5‐95% Non‐Condensing
One Panasonic CR2032 or equivalent Lithium batteries
Four Phillips flat‐head screws
LIMITED WARRANTY
2GIG Technologies, Inc.
2961 W Maple Loop Drive
Lehi, Utah 84043
Technical Support Contact Information
1‐855-244‐4832
Email: [email protected]
Internet: dealer.2gig.com
PN 77‐000004‐001 Rev F
2GIG Copyright © 2012. All rights reserved.