✱ 67
RF XMTR LOW BAT REPORT CODE
✱ 68
CANCEL REPORT CODE
RESTORE REPORT CODES ( ✱ 70 – ✱ 76)
✱ 70
ALARM RESTORE RPT CODE
✱ 71
TROUBLE RESTORE RPT CODE
✱ 72
BYPASS RESTORE RPT CODE
✱ 73
AC RESTORE RPT CODE
✱ 74
LOW BAT RESTORE RPT CODE
✱ 75
RF XMTR LO BAT RST RPT CODE
✱ 76
TEST RESTORE RPT CODE
OUTPUT AND SYSTEM SETUP ( ✱ 77 – ✱ 93)
* 77
DAYLIGHT SAVINGS TIME
START\END MONTH
* 78
DAYLIGHT SAVINGS TIME
START\END WEEKEND
✱ 84
AUTO STAY ARM
✱ 85
CROSS ZONE TIMER
This option not for use in UL installations.
✱ 86
CANCEL VERIFY
✱ 87
MISC. FAULT DELAY TIME
(used with Configurable Zone Types "digit 6")
✱ 89
EVENT LOG FULL REPORT CODE
✱ 90
EVENT LOG ENABLES
✱ 91
OPTION SELECTION
✱ 92
PHONE LINE MONITOR ENABLE
UL: see Inst. Instructions for requirements
✱ 93
No. OF REPORTS IN ARMED PERIOD
PER ZONE (Swinger Suppression)
|
[00]
|
[00]
[0]
|
[00]
|
[00]
|
[00]
|
[00]
|
[00]
|
[00]
0 = Disabled
|
[4][10]
1-12 = January-September (1 = Jan, 2 = Feb, etc)
#+10 = October; #+11 = November; #+12 = December
0 = disabled, 1 = first, 2 = second, 3 = third
|
[1][5]
4 = fourth, 5 = last, 6 = next to last, 7 = third to last
0 = no, 1 = partition 1 only
[0]
2 = partition 2 only, 3 = both partitions
0 = 15 seconds
[0]
1 = 30 seconds
2 = 45 seconds
3 = 60 seconds
4 = 90 seconds
5 = 2 minutes
(assign cross zones on zone list 4, with *81 Menu mode)
0 = no, 1 = yes
[0]
0 = 15 seconds
[0]
1 = 30 seconds
2 = 45 seconds
3 = 60 seconds
4 = 90 seconds
5 = 2 minutes
See box on previous page for report code entries.
|
[00]
0 = None; 1 = Alarm/Alarm Restore
[3]
2 = Trouble/Trouble Restore;
4 = Bypass/Bypass Restore;
NOTE : System messages are
8 = Open/Close. Example: To select "Alarm/Alarm
logged when any non-zero
Restore", and "Open/Close", enter 9 (1 + 8); To select
selection is made.
all, enter #15.
0 = None
[8]
4 = AAV UL: do not use AAV
8 = Exit Delay Restart
Multiple choice example: for AAV (4) + Exit Delay
restart (8) enter # + 12.
Digit 1:: 0 = disabled, 1-15 = 1 min - 15 min
[0,0]
Digit 2:
0 = Keypad display when line is faulted
1 = Keypad display plus keypad trouble sound
2 = Same as "1", plus programmed output device
STARTS. If either partition is armed, external sounder
activates also. NOTE: Output Device must either be
programmed to be STOPPED in field ✱80 or
STOPPED by Code + # + 8 + output number.
0 = Unlimited Reports; 1 = 1 report; 2 = 2 reports
[0]
UL: must be "0"
– 5 –
See box on previous page.
UL: must be enabled if wireless devices are used
See box on previous page.
See box on previous page.
See box on previous page.
See box on previous page.
See box on previous page.
See box on previous page.
See box on previous page.
UL: must be enabled if wireless devices are used
See box on previous page.
6 = 2-1/2 min
7 = 3 min
8 = 4 min
9 = 5 min
#+10 = 6 min
#+11 = 7 min
6 = 2-1/2 min
7 = 3 min
8 = 4 min
9 = 5 min
#+10 = 6 min
#+11 = 7 min
UL: may only be used on non-burglar alarm/ non-fire alarm
zones when used in fire and/or UL burglar alarm installation
(#+10 = 10 min; #+11 = 11 min; #+12 = 12 min;
#+13 = 13 min; #+14 = 14 min; #+15 = 15 min)
#+12 = 8 min
#+13 = 10 min
#+14 = 12 min
#+15 = 15 min
#+12 = 8 min
#+13 = 10 min
#+14 = 12 min
#+15 = 15 min
Drukuj stronę