AFG 13.0AT Podręcznik użytkownika - Strona 17

Przeglądaj online lub pobierz pdf Podręcznik użytkownika dla Bieżnia AFG 13.0AT. AFG 13.0AT 19 stron.
Również dla AFG 13.0AT: Podręcznik użytkownika (20 strony)

Drukuj stronę

PROBLEM:

The treadmill circuit breaker trips during a workout.

SOLUTION:

Verify the following:

• Make sure the treadmill is plugged into a dedicated 20-amp circuit.

• Verify that you do not have the machine on an extension cord or surge protector.

• Confirm that the machine is not plugged into a GFCI-equipped outlet or on a circuit that has a GFCI-equipped outlet on it.

PROBLEM:

The running belt does not stay centered during a workout.

SOLUTION:

Verify the following:

• Make sure the treadmill is on a level surface.

• Verify that the belt is properly tightened and centered (Refer to the Adjustment section for detailed directions).

PROBLEM:

Operating speed appears inaccurate.

SOLUTION:

Auto-calibrate the treadmill:

• Power on the treadmill and have the safety key in position on the

console. Press and hold the elevation "+" and speed "-" buttons for

approximately 5 seconds to enter the Engineering Mode. The console

will beep and "ENG0" appears in the display.

• Press the Speed "+" or "-" button until "ENG2" appears in the display.

• Press, "ENTER" to select. Press, "START" to begin. The treadmill

running belt will begin to move automatically and the auto-calibration

sequence will properly set and store the speed values.

• Upon successful calibration, the treadmill will beep several times. The

console will automatically exit Engineering Mode and return to the

start-up screen.

TROUBLESHOOTING - HEART RATE

Check your exercise environment for sources of interference such as fluorescent lights, computers, underground fencing, home

security systems or appliances containing large motors. These items may cause erratic heart rate readouts.

You may experience an erratic readout under the following conditions:

• Gripping the heart rate handlebars too tight. Try to maintain moderate pressure while holding onto the heart rate handlebars.

• Constant movement and vibration due to constantly holding the heart rate handlebars while exercising. If you are receiving

erratic heart rate readouts, try to only hold the grips long enough to monitor your heart rate.

• When you are breathing heavily during a workout.

• When your hands are constricted by wearing a ring.

• When your hands are dry or cold. Try to moisten your palms by rubbing them together to warm.

• Anyone with heavy arrhythmia.

• Anyone with arteriosclerosis or peripheral circulation disorder.

• Anyone whose skin on the measuring palm is especially thick.

If the above troubleshooting section does not remedy the problem, discontinue use and turn the power off.

PLEASE CALL CUSTOMER TECH SUPPORT AT THE NUMBER ON THE BACK PANEL.

The following information may be asked of you when you call. Please have these items readily available:

• Model Name

• Serial Number

• Date of Purchase (receipt or credit card statement)

In order for Customer Tech Support to service your treadmill they may need to ask detailed questions about the symptoms that are

occurring. Some troubleshooting questions that may be asked are:

• How long has this problem been occurring?

• Does this problem occur with every use? With every user?

• If you are hearing a noise, does it come from the front or the back? What kind of noise is it (thumping, grinding, squeaking,

chirping etc.)?

• Has the machine been lubricated and maintained per the maintenance schedule?

Answering these and other questions will give the technicians the ability to send proper replacement parts and the service necessary

to get you and your AFG treadmill running again!

13.0AT_Rev.1.7.indd 32-33

WARNING

DO NOT

stand on running belt while

calibrating – stand on the guide

rails. Treadmill will fluctuate between

low and high speeds for several

minutes until calibration is complete.

MAIN TENANC E

Cleanliness of your treadmill and its operation environment will keep maintenance problems and service calls to a

minimum. For this reason, we recommend that the following preventive maintenance schedule be followed.

AFTER EACH USE (DAILY)

Clean and inspect, following these steps:

• Turn off the treadmill with the on/off switch, then unplug the power cord at the wall outlet.

• Wipe down the running belt, deck, motor cover, and console casing with a damp cloth. Never use solvents, as they

can cause damage to the treadmill.

• Inspect the power cord. If the power cord is damaged, contact AFG.

• Make sure the power cord is not underneath the treadmill or in any other area where it can become pinched or cut.

• Check the tension and alignment of the running belt. Make sure that the treadmill belt will not damage any other

components on the treadmill by being misaligned.

EVERY WEEK

Clean underneath the treadmill, following these steps:

• Turn off the treadmill with the on/off switch, then unplug the power cord at the wall outlet.

• Move the treadmill to a remote location.

• Wipe or vacuum any dust particles or other objects that may have accumulated underneath the treadmill.

• Return the treadmill to its previous position.

EVERY MONTH - IMPORTANT!

• Turn off the treadmill with the on/off switch, then unplug the power cord at the wall outlet.

• Inspect all assembly bolts of the machine for proper tightness.

• Turn off the treadmill and wait 60 seconds.

• Wait until ALL LED lights turn off.

• Remove screws holding motor cover to the frame. Remove the lower mast bolts in order to slide the motor cover

upwards. While sliding the motor cover up the masts, be careful not to scratch the paint. Prop up the motor cover

to continue.

• Clean the motor and lower board area to eliminate any lint or dust particles that may have accumulated. Failure to

do so may result in premature failure of key electrical components.

• Vacuum and wipe down the belt with a damp cloth. Vacuum any black/white particles that may accumulate around

the unit. These particles may accumulate from normal treadmill use.

EVERY MONTHS OR 10 MILES

It is necessary to lubricate your treadmill running deck every six months

or 150 miles to maintain optimal performance of your treadmill. Once the

treadmill reaches 150 miles, the console will prompt you to lubricate the

treadmill. Only use lubricant provided by AFG!

• TURN OFF THE TREADMILL with the on/off switch, then unplug the

power cord at the wall outlet.

• Loosen both the rear roller bolts. (For best results, place two removable

marks on both sides of the frame and note roller position). Once

the belt is loosened, take the bottle of lubricant and apply it to the

entire top surface of the running deck. Tighten both rear roller bolts

(matching up the marks for proper position) to original position. After

you have applied lubricant, plug in the power cord, insert the safety

key, start the treadmill and walk on the belt for two minutes to spread

the lubricant.

• Lubricate the air shocks with Teflon based spray.

• Once lubrication is complete, reset the console by pressing and holding

'STOP' and Speed '+' buttons for 5 seconds.

Please contact AFG with questions about applying lubricant to your treadmill.

LUB R I C AT I O N

RUNNING BELT

RUNNING DECK

4/1/08 3:41:18 PM