DaytonAudio ME620W Podręcznik użytkownika
Przeglądaj online lub pobierz pdf Podręcznik użytkownika dla Głośniki DaytonAudio ME620W. DaytonAudio ME620W 2 stron. In-wall speaker
Drukuj stronę
One speaker is playing while the other is not:
Check the balance control on the receiver. Make sure it is centered.
●
Loose connection at either the receiver or the speaker. Double check connec-
●
tions.
Bad speaker cable. Replace suspect speaker cable.
●
Receiver cuts on and off:
This could be caused by a short circuit between the positive and negative leads.
●
Check the connections at the back of the receiver, and then at the speaker;
make sure that no strands of wire from one connector are touching the other
connector.
10) Caring For Your In-Wall Speakers
The two most common ways that in-wall speakers are permanently damaged:
1)
Not enough power at higher volumes.
2)
Too much power at higher volumes.
Contrary to conventional wisdom, far more speakers are damaged as a result of under-powering,
than by overpowering. When a receiver runs out of power, it still tries to reproduce the musical
signal by "clipping" the waveform. At high volume levels this clipping introduces gross amounts of
distortion to the speaker, eventually destroying it. If the sound from your speakers starts to sound
distorted, turn down the volume.
Having plenty of reserve power will help your speakers reproduce dynamic contrasts and quick
transients of music much more effectively, but you do have to exercise good judgment; too much
power will also permanently damage a speaker. Again, if you hear distortion, turn the volume down.
Model number
ME520MTM
Woofer
5.25" (x2) Kevlar cone
Tweeter
1" Silk
Frequency response (Hz)
60-20,000
Dimensions H x W x D (in)
7" x 13-3/4" x 2-3/4"
Cut-out size H x W (in)
6" x 12-3/4"
Power handling (RMS/Peak)
50/100
Impedance
8
SPL (1W/1m)
86 ±3dB
Xover point (Hz)
1,800
Xover slope
12dB/octave
Tweeter attenuation (dB)
NA
Type
2-way
Warranty Information
Dayton Audio
products are constructed by industry experts, and are thoroughly tested before shipment.
®
Dayton Audio products are warranted for the period of one year. This warranty is limited to manufacturer
defects, either in materials or workmanship. Dayton Audio is not responsible for any consequential on incon-
sequential damage to any other unit or component or the cost for installation or extraction of any component
of the audio system. In the rare case of a product failure, please contact your place of purchase or call our
Customer Support Department at (937) 743-8248.
Warranty Limitations
There are no other warranties, either express or implied, which extend the foregoing, and there are no warranties
of merchantability or fitness for any particular purpose. The warranty will not cover incidental or consequential
damage due to defective or improper use of products.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Non-Warranty Service: If non-warranty service is required, the product may be sent to the Company for repair/
replacement, transportation prepaid, by calling (937) 743-8248 for details, complete instructions, and service
fee charges.
Specifications
ME620W
ME820W
6.5" Kevlar cone
8" Kevlar cone
1" Silk Pivoting
1" Silk Pivoting
61-20,000
40-20,000
11-3/4" x 7-3/4" x 3-1/4"
13-3/4" x 9-3/4" x 3-3/4"
10-3/4" x 6-3/4"
12-3/4" x 8-3/4"
50/100
80/160
8
87 ±3dB
88 ±3dB
2,500
2,500
12dB/octave
12dB/octave
3, 6, 9
3, 6, 9
2-way
2-way
© Dayton Audio
®
Last Revised: 1/10/2013
Micro-Edge
8
In-Wall Speaker
User Manual
www.daytonaudio.com
Series
TM