Hidden Hitch 87001 Podręcznik - Strona 2
Przeglądaj online lub pobierz pdf Podręcznik dla Akcesoria samochodowe Hidden Hitch 87001. Hidden Hitch 87001 2 stron. Jeep cj5, cj7 & scrambler
Drukuj stronęFor vehicles with enclosed frame.
PARTS IDENTIFICATION / IDENTIFICATION DES PIECES (HARDWARE KIT NO. KA-8001-722)
A) Hitch Assembly
A) Attelage
B) L-Bracket
B) Support en "L"
C) Flat Bracket
C)Support plat
D) Spacer 1/4"
D)Espaceur
E) Spacer 1/2"
E) Espaceur
TOOLS REQUIRED: 1/2" capacity drill; 1/2" diameter drill bit; 3/4" socket; ratchet or impact gun to suit; 100 FT/LB torque wrench.
OUTILS REQUIS: Perceuse de 1/2 po capacitée; foret de 1/2 po diamètre; douille de 3/4 po; manche à rochet ou clé à chocs si nécessaire; clé
dynamométrique à 100 lb-pi.
INSTRUCTIONS
1. Remove bumper or bumperettes from vehicle.
2. Insert hex bolt (1) & (2) through the frame and loosely install l-bracket (B).
3. Loosely attach the hitch assembly (A) to the bumperette mounting holes at the back of the vehicle using the 7/16" hardware (5,6,7,8). (If
bumperettes are going to be reinstalled use 1/2" spacers (E) and 7/16" hardware provided.)
4. Attach l-bracket (B) to the hitch assembly using carriage bolt (4) and flange nut (3).
5. Tighten all bolts; refer to the torque table on the instruction sheet.
HIDDEN HITCH TOW HOOKS
1) Hex bolt
1/2" X 4"
(2)
1) Boulon hexagonal
2) Flatwasher
1/2"
(2)
2) Rondelle plate
3) Flange nut
1/2"
(8)
3) Ecrou à rebord
4) Carriage bolt
1/2"
(8)
4) Boulon de carrosserie
5) Hex bolt
7/16"
(8)
5) Boulon hexagonal
6) Flatwasher
7/16"
(16)
6) Rondelle plate
7) Lockwasher
7/16"
(8)
7) Rondelle de blocage
8) Hex nut
7/16"
(8)
8) Ecrou hexagonal
For vehicles with open frame.
PARTS IDENTIFICATION / IDENTIFICATION DES PIECES (HARDWARE KIT NO. KA-8001-722)
A) Hitch Assembly
A) Attelage
B) L-Bracket
B) Support en "L"
C) Flat Bracket
C)Support plat
D) Spacer 1/4"
D)Espaceur
E) Spacer 1/2"
E) Espaceur
TOOLS REQUIRED:1/2" capacity drill; 1/2" diameter drill bit; 3/4" socket; ratchet or impact gun to suit; 100 FT/LB torque wrench.
OUTILS REQUIS: Perceuse de 1/2 po capacitée; foret de 1/2 po diamètre; douille de 3/4 po; manche à rochet ou clé à chocs si nécessaire; clé
dynamométrique à 100 lb-pi.
INSTRUCTIONS
1. Remove bumper or bumperettes from vehicle.
2. Loosely attach the hitch assembly (A) to the bumperette mounting holes at the back of the vehicle using the 7/16" hardware (5,6,7,8). (If
bumperettes are going to be reinstalled use 1/2" spacers and 7/16" hardware provided.)
3. Attach flat bracket (C) to the hitch assembly using carriage bolts (4) and flange nuts (3).
4. Use the holes in the flat bracket (C) as a guide to drill two holes in the bottom of the frame.
5. Use carriage bolts (4) and flange nuts (3) to attach flat brackets to the frame.
6. Tighten all bolts; refer to the torque table on the instruction sheet.
1) Hex bolt
1/2" X 4"
(2)
1) Boulon hexagonal
2) Flatwasher
1/2"
(2)
2) Rondelle plate
3) Flange nut
1/2"
(8)
3) Ecrou à rebord
4) Carriage bolt
1/2"
(8)
4) Boulon de carrosserie
5) Hex bolt
7/16"
(8)
5) Boulon hexagonal
6) Flatwasher
7/16"
(16)
6) Rondelle plate
7) Lockwasher
7/16"
(8)
7) Rondelle de blocage
8) Hex nut
7/16"
(8)
8) Ecrou hexagonal
HITCH MOUNTS