Celestron NexStar EVOLUTION 12091 Instrukcja obsługi - Strona 9
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Teleskop Celestron NexStar EVOLUTION 12091. Celestron NexStar EVOLUTION 12091 15 stron. Nexstar evolution series 6/8/9.25" telescopes
Drukuj stronę
the eyepiece using the direction keys on the hand control-
ler and press the ALIGN button . This will accept the star
as the first alignment position . (There is no need to adjust
the slewing rate of the motors after each alignment step .
The NexStar automatically selects the best slewing rate for
aligning objects in both the finderscope and the eyepiece) .
7 . For the second alignment object, choose a bright star or
planet as far as possible from the first alignment object .
Once again, use the direction keys to center the object in
the finderscope and press ENTER . Center the object in
the eyepiece, then press the ALIGN button .
8 . Repeat the process for the third alignment star . When the
telescope has been aligned to the final stars, the display
will read "Align Success . "
Aligning with Auto Two Star
After the first star is selected and centered, the second star
will automatically be chosen for the best possible alignment .
Once selected, the telescope will automatically slew to the
second alignment star to complete the alignment .
1 . Flip the NexStar's power switch on . The hand control will
display "Verifying Packages..." After a few seconds it will
display "Evolution . " Scroll down using the "9" Scroll key
and press ENTER to choose Auto Two Star .
2 . Press ENTER and you will be prompted to enter the local
time in 24-hour format . Ex . 21:00 for 9PM .
3 . Select Daylight Savings or Standard Time, toggle the 6 &
9 (up and down scrolling keys) to change .
4 . Select time zone, then enter the date . Press ENTER each
time to proceed to the next prompt .
5 . The display will now prompt you to "Select Star 1" from
the displayed list on the hand control . Use Up and Down
scroll keys (6 and 9 on the keypad) to scroll to the desired
star and then press ENTER .
6 . Use the direction keys to slew the telescope to the star
you selected . Center the star in the StarPointer and press
ENTER . Finally, center the star in the eyepiece and press
ALIGN .
7 . The hand control will automatically display the most
suitable second alignment star that is above the horizon .
Press ENTER to automatically slew the telescope to the
displayed star . If for some reason you do not wish to select
this star (perhaps it is behind a tree or building), you can
either:
• Press the UNDO button to display the next most suitable
star for alignment .
• Use the UP and DOWN scroll keys to manually select any
star you wish from the entire list of available stars .
8 . Repeat the same process of centering the star in your
StarPointer, press ENTER, then center in your eyepiece
and press ALIGN .
When the telescope has been aligned to both stars the
display will read Alignment Success . You are now ready to
find your first object .
16 I
Using a Wedge with EQ North /
EQ South Alignment
EQ North and EQ South Alignments assist the user in
aligning the telescope when polar aligned on an optional
equatorial wedge .
EQ AutoAlign
1 . Select EQ North (for northern hemisphere) or South (for
southern hemisphere) Align from the alignment options
and press ENTER .
2 . Enter time, date, and location information as with all other
alignments .
3 . Select EQ AutoAlign method and press ENTER
4 . Use the direction arrow keys to move the telescope until
the altitude and meridian index markers are aligned . The
altitude index marker is located at the top of the fork arm,
and the meridian marker is on the base of the fork arm .
The tube should be perpendicular to the fork arm and
facing the meridian .
5 . The display will now prompt you to "Select Star 1" from
the displayed list on the hand control . Use Up and Down
scroll keys (6 and 9 on the keypad) to scroll to the de-
sired star and then press ENTER .
6 . Use the direction keys to slew the telescope to the star
you selected . Center the star in the StarPointer and press
ENTER . Finally, center the star in the eyepiece and press
ALIGN .
7 . The hand control will automatically display the most
suitable second alignment star that is above the horizon .
Press ENTER to automatically slew the telescope to the
displayed star . If for some reason you do not wish to select
this star (perhaps it is behind a tree or building), you can
either:
• Press the UNDO button to display the next most suitable
star for alignment .
• Use the UP and DOWN scroll keys to manually select any
star you wish from the entire list of available stars .
8 . Repeat the same process of centering the star in your
StarPointer, press ENTER, then center in your eyepiece
and press ALIGN .
When the telescope has been aligned to both stars the
display will read Alignment Success . You are now ready to
find your first object . Tracking will now occur equatorially,
moving in just one direction to keep the object centered in
the telescope's field of view without rotating . This tracking is
suitable for astroimaging .
NexStar Evolution Telescope
Settings in NexStar+ Hand Control
Press Menu, scroll to the "Peripherals" menu and press
ENTER. Here, you can control L .E .D . brightness of the logo
lights and accessory tray lighting, check the battery status, or
set more advanced features including external power supply
and USB charge port settings .
Adjust the L.E.D. Brightness
1 . Scroll to "Mount Lights" and press ENTER .
2 . Scroll to select Tray Light, WiFi Light, or Logo Light and
press ENTER .
3 . Select a brightness value from 0-10, 0 being OFF, and
10 being fully lit . Press ENTER and the new brightness
setting will take effect .
Power
1 . Scroll to "Power" and press ENTER .
2 . Scroll to select "Status" or "External Power" and press
ENTER
• Status will display the battery voltage, if the battery
charge state is High, Medium, or Low, and if the battery
is charging or discharging .
• External Power allows you to select a higher input current
if you are using a higher capacity power supply . Values
can be between 2 and 5 amperes as specified on your
power supply . Do not change this setting unless you
are using a larger capacity supply . The included power
supply should always be set to 2 .0A .
WiFi
1 . Scroll to "WiFi" and press ENTER .
2 . Scroll to select "Status" or "Enable/Disable" and press
ENTER
• Status will display the WiFi mode, Direct Connect or
Access Point, and whether or not the WiFi is connected
to a network
• Enable/Disable will optionally allow you to disable the
WiFi broadcast . The WiFi L .E .D . will shut off indicating it
has been disabled . Every time you power off and on the
mount again, this setting defaults to Enabled .
USB Charge Port
1 . Scroll to "Charge Port" and press ENTER .
2 . Press ENTER to toggle between "Automatic" or "Always
On" . "Always On" keeps the charge port going, even in a
low battery condition . "Automatic" automatically disables
the USB Charge Port when battery power is low .
I 17