Dynamic DT1250 Instrukcja obsługi - Strona 2

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Sprzęt do zwalczania owadów Dynamic DT1250. Dynamic DT1250 3 stron. Flying insect trap
Również dla Dynamic DT1250: Instrukcja obsługi (3 strony)

Drukuj stronę

OWNER'S MANUAL

FLYING INSECT TRAP

MODEL: DTl 2S0

Thank you for purchasing the

DYNATRAP® flying insect trap!

IMPORTANT SAFETY INSTRUCTIONS

WARNING, When using electric appliances, basic precautions should always be followed, including the

following:

- To disconnect, turn all controls lo the off ('O") position, then remove plug from outlet.

- Unplug from outlet when not

use and before servicing or cleaning.

- To reduce the risk of electrical shock, do not put appliance in

water

or other liquid.

- This appliance is provided with double

insulation.

Use only identical replacement

parts.

- Connect only to a circuit that is protected by a ground-fault circuit-interrupter (GFCI).

See instructions for Servicing of Double-Insulated

Appliances.

INSTRUCTIONS FOR DOUBLE-INSULATED, CORD-CONNECTED APPLIANCES:

In a double-insulated appliance, two systems of insulation ore provided instead of grounding. No

grounding

means is provided

on a double-insulated appliance, nor should a means for grounding be added to the appliance. Servicing of a double-insulated

appliance requires extreme core and knowledge of the system, and should be done only by qualified service

personnel.

Replacement ports for a double-insulated appliance must be identical to those ports in the

appliance.

IMPORTANT SAFETY INSTRUCTIONS

Please read these instructions before using the DYNATRAP® Insect Trap and keep for future reference.

l. Always turn unit off and disconnect plug before servicing, cleaning, or changing bulb.

Do not position the unit near heat, gos, oil or other flammable

materials.

3. Place product out of reach from

children.

4. Never operate this product if it hos a damaged cord or plug, ii

is not working properly, ii

hos been dropped or

damaged, or if ii hos been dropped into

water.

5. This product is equipped with 2-conductor cord and 2-prong polarized plug as

safety feature. This plug will fit in a

polarized outlet only one way. If the plug does not fully lit in the outlet, then reverse the plug. If it still does not lit,

then contact a qualified

electrician.

To reduce the risk of electrical shock, only plug into a properly installed outlet.

Do not attempt to defeat this safety feature.

Do not insert fingers or any foreign objects into the unit while ii is connected to an electrical outlet.

Collected insects within the unit may contribute to fire, so clean insects from the unit

frequent~.

8. Do not clean this product with water

spray.

Do not place where ii con foll into water, or near flammable materials.

Do not touch fan while in

motion.

l 0. Do not abuse cord--never carry or hong

unit

by cord or yank it to disconnect from receptacle. Keep cord away from heat,

oil, or sharp

edges.

11. Extension cords used with this product must be marked with suffix letters "W-A" and with a tog stating "Suitable for Use

with Outdoor Appliances".

12. Use only extension cords that hove plug and receptacles that match the product plug. Replace or repair damaged cords.

INSTALLATION & OPERATING INSTRUCTIONS

Unpack unit. Save carton for off-season storage (if

needed).

Assemble

stand:

Pull the cord tight through the poll stand. Turn base on its side and insert bottom

threaded plastic p iece into hose, connecting to the threaded plastic

cop.

Twist threaded plastic cop

clockwise to

tighten.

Complete installation by aligning upper ond lower support tube and inserting the

bor secttons. (For more detailed

instructions,

please refer to the assembly guide.)

Plug cord into on outlet or UL listed extension cord as described in ' I MPORTANT SAFEIY

INSTRUCTIONS".

Hold the Power switch on the side of the revolving rotation

door.

Twist the unit to the 'Power ON"

position.

When you hear a 'click", the machine is turned

on.

For best catch results leave unit on at all

times,

except when cleaning or

servicing.

Catch rote activity will be higher at night. For best catch results ii is recommended to keep the unit away from compettng light

sources.

Intended for household use

only.

It is recommended to place the unit at least 10 to 20 feet away from where people will be sitting.

This unit is all weather resistant- designed for outdoor use including rainy

conditions.

CLEANING

Frequent cleaning will prolong the life of the unit, ensure lire prevention and provide for more efficient operation.

Be sure to clean the unit once per week

To clean, hold the switch on the revolving rotation door and turn

lo the ' P OWER OFF"

position.

After hearing the "click",

the machine is turned off. Unplug the unit.

For weekly cleaning, remove the screw securing the retaining cage and then twist the cage

clockwise.

Remove any buildup from the inside

of the retaining cage and Ion with a brush

(included).

For major cleaning, remove the four screws securing the Ion housing to the light housing. After removing the screws, gently pull the Ion

housing away from the light

housing.

Using a soft brush, remove dirt and debris from the light

housing.

Once the cleaning process hos

been completed, align the screw holes in the Ion housing with the screw holes in the lighting unit and tighten the screws to the base of

the lighting

unit.

When replacing the retaining cage - DO NOT press/push against the screen windows.

REPLACING BULB

The light bulb life expectancy is approximately 3,000 hours (or about 4 months), and should be replaced regularly lo ensure opttmol UV

effectiveness. Even though the bulb's light may be visible to you, its ability to attract insects diminishes over

time.

Turn power switch to "off"

position.

UNPLUG UNIT, and allow bulb lo cool before replacing.

Remove the screw securing the retaining cage and then remove the retaining cage by lwisttng the cage

clockwise.

Turn the unit upside

down.

Remove the lour screws securing the Ion housing to the light

housing.

After removing the screws, gently pull the Ion housing away from

the light housing. Using o soft brush, remove dirt and debris from the light

housing.

Once the cleaning process hos been completed,

untighten the screw securing the base of the light bulb to the light

housing.

Slide the metal bracket lo the

side.

Cover the bulb with a

cloth to protect your linger and

hand.

Grasp the bulb (with your hand and lingers protected by the cloth) and gently pull the bulb from

the socket.

Remove any debris from the lamp socket with a brush before

inserting

the new

bulb.

Replace the metal plate over the base of the bulb

and tighten the retaining screw.

Align the screw holes in the Ion housing with the screw holes

the lighttng unit and tighten the screws to the hose of the lighting

unit.

Replace the retaining cage at the bottom of the unit.

Replacement Fluorescent Bulbs con be found at your local retailer or con be ordered directly from

IC.

by colling

1-877-403-TRAP (8727) or visiting

www.dynotrap.com.

HOW THE DYNATRAP® INSECT TRAP WORKS

F~ing insects are attracted to the unit by UV light and CO2 that is

generated by the photo-catalysis between the UV lamps and spe-

cial

Ti02

coating. The Ion then pulls the insects into the screened

base, trapping them until they dehydrate and

die.

The base con be

removed, allowing the

contents

to be periodical~ emptied into

the trash. The see-through screen shows the insects trapped in the

comportment, alerting you when the net needs to be

emptied.

TROUBLESHOOTING

Problem:

Possible cause:

Correction:

Bulb does not illuminate

1. No electrical power.

1. Check plug and receptacle and fuse or circuit breaker.

and fan does not

spin.

Check to make sure power is switched to the

"on" position.

Bulb illuminates, but fan

1. Shorted

fan.

1. UNPLUG UNIT: Examine fan to see that it is free from

does not spin.

foreign material, dirt or build-up of dead

insects.

Cleon unit as in "CLEANING" section.

Fon spins, but bulb does

1. Bulb not seated

1. Check all sockets for proper bulb seating and alignment.

not illuminate.

properly.

2. Replace bulb if needed following instructions under

Burnt out bulb.

"Replacing

Bulb".

LIMITED WARRANTY

DWNlft\lC.

warranties to the original purchaser that this product is free from defective materials and

workmanship. This warranty is limited to remedy any defective par! for a period of one year from dale of

original date of purchase. Retain your original receipt as proof of purchase. This warranty does not apply

to the light bulb, nor to, in our judgment, misuse or abuse. If this unit has been altered, no warranty is in

force. This warranty does not apply

this unit is purchased outside the United States, excluding Canada

and Mexico. In no case shall

DWtUft\l(.

be liable for any accidental, punitive, consequential, or any other

damages of any kind for breach of this or any other warranty, expressed or implied, whatsoever. Some

stales do not allow limitation on how long an implied warranty lasts, so the above limitation or exclusion

may not apply to you. This warranty gives you specific legal rights, and you may also have other rights

that vary from state to state.

PARTS

ACCESSORIES AVAILABLE

PART

DESCRIPTION

41050

7-Watt Replacement Fluorescent Bulb

piece)

41051

Fon Blade Replacement

41052

Fon Blade and DC Motor Ultra-Long Life Replacement

41053

Retaining Cage

41061

Lorge Capacity Net (lo be used instead of the Retaining Cage, suitable for extra large catch performance)

l ~

\'IIC.

Dynamic Solutions Worldwide, LL(

12247 W

Fairview

Ave.

Milwaukee, WI 53226

Phone:

414-431-2819

Fox: 414-453-9975

Toll free: 1-877-403-TRAP (8727)

Or visit us online at www.dynotrop.com

EPA Est.

No.

08Bll9-CHN-001

EPA Est.

No.

OB7B37-Wl-001

SAVE THESE INSTRUCTIONS

lntertek