Dynamic CCTV DVR-8 Podręcznik użytkownika - Strona 11

Przeglądaj online lub pobierz pdf Podręcznik użytkownika dla DVR Dynamic CCTV DVR-8. Dynamic CCTV DVR-8 18 stron. 8 channel digital video multiplex recorder

Drukuj stronę

8 channel stand-alone DVMR

ALL ABOUT IMAGE RECOGNITION & PROCESSING

5) BAUDRATE SETUP

To control PTZ camera connected to DVMR unit, you

have to set baud rate of communication between PTZ

camera and DVMR unit.

To set baudrate, move half-tone green bar on baudrate you

want to select, and press [ENTER] button then CURRENT

VALUE is changed to the value you selected.

CONFIRMATION VIA RS485 PORT on the bottom of

BAUDRATE SETUP is to test if communication between

DVMR unit and PTX camera with set baudrate is done

correctly. Move half-tone green bar to CONFIRMATION VIA

RS485 PORT, and press [ENTER] button. Then you can

see TEST STRING sent by DVMR unit is displayed on your

PC, in case you also connected DVMR unit to PC via RS-

232C port.

To save settings and exit, press [MENU] button.

6) PASSWORD SETUP

You can set your own password in PASSWORD SETUP.

DVMR system verify users entering into SETUP menu and

users who input correct password is allowed to access

SETUP menu and change any settings in SETUP menu.

Also, you have to input proper password in SETTING in

remote viewer(client program) to access DVMR unit via IP

network, too.

Sequence to change password is as follows.

- Input current password in the first line and press [ENTER].

- Input new password in the second line and press [ENTER].

- Input new password again to confirm it and press [ENTER].

- Then "PASSWORD CHANGE" is displayed and changing

password is completed.

Memorize new password and also keep it secretly.

In case you forgot password, contact dealer from which

you purchased DVMR unit. All of our dealers have master

password which will enables you to enter into

PASSWORD SETUP menu to generate new password.

3. Operation

BAUDRATE SETUP

1200 BPS

2400 BPS

CURRENT SPEED

4800 BPS

9600 BPS

19200 BPS

SELECT

, THEN ENTER

BAUDRATE SETUP

CURRENT PASSWORD : --------

NEW PASSWORD

: --------

CONFIRM PASSWORD

: --------

INPUT YOUR OWN PASSWORD,

THEN PRESS [ENTER]

TO EXIT, PRESS [MENU]

PASSWORD SETUP

8 channel stand-alone DVMR

ALL ABOUT IMAGE RECOGNITION & PROCESSING

2-5. Sensor Connection

Connect sensors to D-SUB 25 Pin as specified below.

You can connect dry-contact type sensors. In case of sensors with TTL output (5 Volts system), GND of

sensor must be connected to GND of DVMR unit and signal line to alarm input from D1 to D16 as shown

in following figure.

Short-circuit between any of D1 from D16 and GND is recognized as an alarm.

All GNDs are connected to each other on circuit.

SENSOR

RELAY Output

14(GND)

15(GND)

16(GND)

17(GND)

18(GND)

19(GND)

20(GND)

21(GND)

Relay output is output in case there is an alarm input, and is connected to external device using

COM-NO (Normal Open) or COM-NC (Normal Close) contact.

2-6. Network Connection

RS-232C : Connection to PC to operate DVMR

RS 485 : Connection to PTZ camera

RJ-45 (ETHERNET) : Connection to LAN, WAN or Internet

VGA : Connection to PC monitor

ALARM/ RELAY

o r t

PTZ

CAMERA

RS-232C/485

ETHERNET

For more details, refer to arrangements RS-232c pins in page 29.

2. Installation

ALARM INPUT

COM

GND