HIFEI Technology 200A-KIII Pro-HV Instrukcja obsługi

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Pilot zdalnego sterowania HIFEI Technology 200A-KIII Pro-HV. HIFEI Technology 200A-KIII Pro-HV 10 stron.

Drukuj stronę

INSTRUCTIONS

Safety

The brushless ESC is used for R/C electric powered model

airplane and helicopters, which are not toys. ONLY adults

can run it correctly according to this instructions, young

children must run it with guardianship of adults.

Please keep the propeller away from your body and others

all the time when the battery is connected.

It is suggested that you remove the propeller when you are

working on the airplane with the battery connected.

It is suggested that you remover the pinion when you are

working on a helicopter with the battery connected.

Please observe all local laws regarding the flying of remote

control airplane.

Never fly over others or near crowds.

Before beginning flying, turn on the transmitter BEFORE

powering on the receiver.

When finish the running, power off the receiver BEFORE

turning off the transmitter.

Never disconnect the battery pack while the brushless motor

is running, as this could cause damage to the speed

controller and/or motor. And such damage would not

covered under manufacturer‟s WARRANTY.

Features of Kingkong III Pro ESC

• 32-bit Microprocessor with up to 80MHz frequency.

• 4-14S Lipo support

• Max continuous current 160A / 200A in full

throttle ( KIII Pro 160A HV / KIII Pro 200A HV )

• Active FreeWheeling optional

• Motor PWM frequency 8-32K Hz

• Throttle resolution up to 1uS

• Throttle signal refresh rate up to 1K Hz

• Integrated RPM sensor to simplify the wiring for

external Governor

• Optimized the Governor Algorithm to ensure the

head speed more stable

• Fully CNC aluminum housing to efficient the heat

dissipation

Kingkong III Pro USER MANUALS

KingKongIII Pro

• Built-In data Logger ( logging parameters: battery

voltage/current/throttle output/temperature/motor

RPM)

• Combine with WiFi dongle (sold separately) to pro-

gram setting the parameters of esc and telemetry the

real-time flight data by any kind of smart cell phone

• Max RPM 240000 with 2 pole motor ( Heli Mode:

Max electric RPM 160000 )

Kingkong III Pro Series ESC

ESC

Voltage Conti. Amp

160A-KIII

4-14S

Pro-HV

Lipo

200A-KIII

4-14S

Pro-HV

Lipo

100A-KIII

3-6S

Pro-6S Lite

Lipo

KIII

Pro

3-6S

100A-6S

Lipo

Surge current could be reached under the condition of ESC in contact

with 5mph airflow of 25 (77F) or cooler air at full throttle.

Install your ESC

Add battery connector

You must attach a quality battery connector of your choice to

the red (positive) and black (negative) of power wires. Well

solder the connectors to the wires and ENSURE THAT PO-

LARITY IS CORRECT (red wire to battery red wire, black

wire to battery black wire). Follow the instructions provided

with battery connector.

Connect ESC to motor

Suggested to solder quality and corresponding size golden bul-

let connectors for your motor to the motor wires coming from

ESC.

*Swapping any two motor wires connection can change rota-

tion direction.

Connect to receiver

Connect the receiver lead (consisted of brown, red and orange

small wires with a black plastic connector on the end ) to throt-

tle channel of receiver in right polarity, brown wire to negative,

red wire to positive, orange wire to signal.

Kingkong III Pro HV ESC are OPTO, so separate receiver

battery or UBEC to supply power for receiver is required.

www.hifei.com

Surge

Amp(5s)*

160amp

220amp

200amp

250amp

100amp

130amp

100amp

140amp

Page 1

BEC

Couple-

OPTO

Couple-

OPTO

Switching

Max 5A

Switching

Max

5A/6V