DYNAMICS GROUP Dings 6-60000-535 Instrukcja obsługi - Strona 9

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Urządzenia przemysłowe DYNAMICS GROUP Dings 6-60000-535. DYNAMICS GROUP Dings 6-60000-535 12 stron. End-mount brake, enclosed wpdt housing with deep drawn cover

Drukuj stronę

WARNING:

Brake performance and features must be carefully matched

to the requirements of the application.

Consideration must be given to torque requirements,

especially where an overhauling condition exists, as well

as thermal capacity, ambient temperature, atmospheric

explosion hazards, type of enclosure and any other

al conditions.

Improper selection and installation of a brake and/or lack

of maintenance may cause brake failure that could result in

damage to property and/or injury to personnel.

If injury to personnel could be caused by brake failure,

additional means must be provided to insure safety of

personnel.

GENERAL SAFETY INFORMATION

NOTE: These brakes are not intended for accurate positioning

applications. They are designed for applications that require

rapid stopping and holding power, such as on conveyors, door

openers, etc.

For applications with high inertia-type loads or rapid

cycling, the thermal capacity of the brake must be

considered.

Observe all local electrical and safety codes, as well as

the National Electrical Code (NEC) and the Occupational

Safety and Health Act (OSHA).

Brake motors and brake gearmotors must be securely and

adequately grounded. This can be accomplished by wiring

with a grounded metal-clad raceway system, by using a

separate ground wire connected to the bare metal of the

motor frame, or other suitable means. Refer to NEC Article

250 (Grounding) for additional information. All wiring

should be done by a qualified electrician.

Always disconnect power before working on or near a brake

motor, a brake gearmotor, or its connected load. If the

power disconnect point is out of sight, lock it in the open

position and tag it to prevent unexpected application of

power.

When working on the brake, be sure the load is completely

removed, secured or blocked to prevent injury or property

damage.

Provide guarding for all moving parts.

Be careful when touching the exterior of an operating

motor, gearmotor or brake. It may be hot enough to cause

injury or to be painful. This condition is normal for modern

motors, which operate at higher temperatures when running

at rated load and voltage.

Protect all electrical lead wires and power cables against

contact with sharp objects or moving parts.

Do not kink electrical lead wires and power cables, and

never allow them to touch oil, grease, hot surfaces or

chemicals.

WARRANTY

Seller warrants products manufactured by it and supplied

hereunder to be free from defects in materials and workmanship

under normal use and proper maintenance for a period of twelve

months from date of shipment. If within such period any such

products shall be proved to Seller's reasonable satisfaction to

unusu-

be defective, such products shall be repaired or replaced at

Seller's option. Seller's obligation and Buyer's exclusive remedy

hereunder shall be limited to such repair and replacement and

shall be conditioned upon Seller's receiving written notice of

any alleged defect no later than 10 days after its discovery

within the warranty period and, at Seller's option, the return

of such products to Seller, f.o.b. its factory, when such return

is feasible. Seller reserves the right to satisfy its warranty

obligation in full by reimbursing Buyer for all payments it

makes hereunder, and Buyer shall thereupon return the products

to Seller. Seller shall have the right to remedy such defects.

Seller makes no warranty with respect to wear or use items such

as belts, chains, sprockets, discs and coils, all of which are sold

strictly AS IS.

T he f oreg o in g w a rra ntie s are e xc lusiv e and in

l ieu of a ll other express and implied warranties

(except of title) including b u t no t lim ited t o im plie d

w ar ra nt ies o f me rch anta bility, fitne ss f o r a

pa rti cula r p u rpos e, p e rfo rm an c e, o r o the r w ise,

and in no event shall the Seller be liable for claims (based

upon breach of express or implied warranty, negligence, product

liability, or otherwise) for any other damages, whether direct,

immediate, incidental, foreseeable, consequential, or special.